SkyLink GT-100 User Manual

Download Operation & user’s manual of SkyLink GT-100 Garage Door Opener for Free or View it Online on All-Guides.com.

Brand: SkyLink

Category: Garage Door Opener

Type: Operation & user’s manual for SkyLink GT-100

Pages: 4 (0.1 Mb)

Download SkyLink GT-100 Operation & user’s manual

SkyLink GT-100 Operation & user’s manual - Page 1
1
SkyLink GT-100 Operation & user’s manual - Page 2
2
SkyLink GT-100 Operation & user’s manual - Page 3
3
SkyLink GT-100 Operation & user’s manual - Page 4
4
1. INTRODUCTION
Model GT-100Garage Door Closer
TM
Congratulations on your purchase of the Skylink
®
Garage Door Closer
Model GT-100. Skylink
®
Garage Door Closer is very easy to install, and
provides you with the peace of mind you have been looking for by
knowing your garage door will not be left open anymore. Skylink
®
Garage Door Closer consists of 2 units:
Wall Console does not require any battery to operate and it can replace
most of the existing garage door opener’s push buttons. Garage Door
Sensor is battery operated and can be mounted on to the garage door by
double sided tape or screws. These 2 units operate wirelessly which
simplifies the installation.
Programming is very simple, you can select the time you would like the
door to be closed after it has been opened. The selectable door closing
times are 2 minutes, 5 minutes, 10 minutes and 20 minutes.
Garage Door
Monitor
TM
Sensor
(Battery Included)
GS-101
2. INSTALLATION (CONT)
Before installing the Skylink
®
garage door closer, ensure your garage
door is equipped with an external entrapment protection device, such
as an infrared beam sensor which “sees” an object obstructing the door
without having actual contact with the object. A Garage door opener does
that not have the auto reversing mechanism should be replaced by one that
has the auto reversing mechanism feature and the garage door closer
must not be installed on garage a door opener without this feature.
Without a properly working safety reversal system, a person could be
seriously injured or killed by a closing garage door.
WARNING
2. INSTALLATION
Unplug the power cord of your garage door opener
before installation to ensure power is not connected.
WARNING
The installation involves 2 units:
1) Garage Door Monitor
TM
Sensor
2) Wall Console
Garage Door Monitor
TM
Sensor
Step 1 – Select a spot on your garage door to mount
the sensor
Before you install the sensor onto the garage door,
make sure the garage door is closed. The sensor
assembly should be mounted on one of the vertical
supports of your garage door near the bottom.
When the door is closed, the detection rod should be retracted. When
the door is open, the detection rod will be extended.
Note:
When the garage door is opening/closing,
make sure the sensor does not interfere with
the safety reversing sensor or safety beam
sensor supplied with your existing garage
door opener.
Step 2 – Mount the sensor on to your garage door
You can mount the sensor onto your garage
door with double-sided foam tape if the sur-
face of your garage door is smooth and clean
enough to provide a good adhesive surface,
such surface can usually be found on a me tal
garage door. Please ensure the surface is
smooth and clean. Important: The bottom
of the sensor should be 1/2 inch above
the ground. (Refer to Diagram A)
For w ooden garage doors, it is recommended
to mount the sensor with screws on to the
garage door with 3 x 18 screws provided.
4 Screws
Double-sided
foam tape
1/2 Inch
Note: Ensure you straighten up the antenna
on the receiver to receive the best possible
reception.
Diagram A
Wall Console
The GT-100R Wall Console replaces most garage door “push buttons” or
“wall consoles”. There are 2 different kinds of “push buttons”.
1) Single button
2) Multi-Function Wall Console
1) Single button
If your garage door opener equips with a single button “push button”,
you can replace the existing push button with Skylink
®
Garage Door
Closer Wall Console GT-100R. Please follow the procedures below.
1. Remove the existing push button by removing
the screws.
2. Disconnect the 2 wires that are connected to
the existing push button.
3. Connect these 2 wires to the 2 terminals on the
GT-100R Wall Console. Loosen the 2 screws
on the terminals, feed the 2 wires to the 2
terminals and tighten 2 screws to secure the
2 wires.
4. After connecting the 2 wires, the red LED under-
neath the push button will be on. The GT-100R
is now charging up. The GT-100R will be fully
charged when the buzzer emits a beep (approx
10 seconds to 1 minute depending on the brand
of garage door opener), the red LED will then
flash slowly. The GT-100R is now ready to operate.
5. Mount the Wall Console to the wall with 2 screws.
6. Straighten up the antenna on the GT-100R.
Remove
existing
wires
One of
Vertical
Supports
Door closed
Door open
Remove the battery
isolator
4 pcs 3 x 18 screws
2 pcs 3.5 x 25 screws
Double-sided
foam tape
3V Lithium battery
Extension wires
Wall Console
GT-100R