Home | About | Contact

Accusplit Eagle 1540M2 Operating Instructions

Download Operating instructions of Accusplit Eagle 1540M2 Pedometer for Free or View it Online on All-Guides.com.

Brand: Accusplit

Category: Pedometer

Type: Operating instructions for Accusplit Eagle 1540M2

Pages: 2 (0.19 Mb)

Download Accusplit Eagle 1540M2 Operating instructions

Accusplit Eagle 1540M2 Operating instructions - Page 1
1
Accusplit Eagle 1540M2 Operating instructions - Page 2
2
Page 1
background image

SETTING UP YOUR PEDOMETER 

To record your distance and calories accurately, you will 

need to set your stride length.

CHOOSING A MEASUREMENT SYSTEM

This unit is initially set to use English measurement units 

(Miles). To change the unit back and forth between English 

and Metric units (Kilometers). press the yellow RESET 

button for 5 seconds.

Finding Your Stride Length

: Your stride length is the 

length of one of your steps, measured from “toe to toe.” 

To measure, walk 10 steps with your normal stride and 

measure the TOTAL DISTANCE from the toe of your starting 

step to the toe of your 10

th

 step (see diagram below). Divide 

the TOTAL DISTANCE by 10. This is your stride length. 

Example: If you walk 22 feet, your stride length is 2.2 feet.

Setting Your Stride Length:

 Press the black MODE button 

until the arrow on right hand side of display points to “M” 

(miles). Press the gray SET button for at least two seconds 

to enter setting mode. Display will shift to show stride. Press 

and hold down the gray SET button to increase stride length. 

Press and hold the yellow RESET button to decrease stride 

length. Press the black MODE button to exit setting mode.  

(For example, “F 1.95” means stride is set to 1.95 feet.) 

WEARING YOUR PEDOMETER

While gently holding the belt clip open, slide the pedometer onto your 

belt or the top edge of your pants or skirt. It should fit snugly and 

level, above one knee. 

Note:

 The pedometer should be as vertical as possible. Walkers with 

larger stomachs may find it helpful to wear the pedometer farther 

back on the body, toward one hip. 

The cover must be closed for the pedometer to work.

 To avoid 

losing or dropping your pedometer, use the included leash and clip to 

fasten the pedometer securely to your clothing. 

Attaching the Leash: 

Attach the pedometer to the leash by looping 

the leash around the pedometer belt clip. Next, clasp the waistband 

of your clothing with the attached clip. You can also use a safety pin 

to fasten the leash to your clothing, loop the leash through your belt 

or belt loop, or use a badge holder. 

ACCUSPLIT, Inc.  •  6120 Stoneridge Mall Rd. Suite 210  •  Pleasonton, CA 94588

800-965-2008  •  925-226-0888  •  FAX 925-463-0147  •   www.ACCUSPLIT.com   •  [email protected]

Congratulations on taking the first step to wellness with your purchase 

of an ACCUSPLIT pedometer. It’s easy to set up your new pedometer. 

Just follow the steps below, and start walking!

10 steps

MEMORY PEDOMETER

OPERATING INSTRUCTIONS

ACCUSPLIT®
       EAGLE

 

1540M2

DISPLAY MODES
•   “D”– “Day’s Steps”

  Counts steps taken since last ReSet. 

  Reset daily to count  each day’s steps.

•  “t”–”total Steps”

  Keeps track of all steps taken, even after 

  Day’s Steps are reset.

•  “M”(miles) –”K” (kilometers)

  Shows distance walked since last reset 

  of “total Steps.”

970-045

ACCUSPLIT 

EAGLE

AccuSTEP

1540M2

10000.org

MODE

SET

RESET

(2S)

STEP

DIST

TW15G

D
T
M
K

Yellow:

ReSet

Gray:

Set

Black:

MODe

“D” = Day

“T” = Total

“M” = Miles

“K” = Kilometers

First, loop the 

pedometer clip

Next, loop the metal clip, then 

clasp clothing

Or, loop a  

badge holder, then 

 put into pocket

(Badge holder not included)

Or, loop a belt  

or belt loop

VIEWING YOUR RESULTS

Once you put on your pedometer with the cover closed, it will 

automatically begin to record your steps and distance. Repeatedly 

press the black MODE button to cycle through the pedometer 

modes: DAILY STEPS → TOTAL STEPS → DISTANCE →  

DAILY STEPS

AUTO MOVEMENT SENSOR

1. To filter out random movements, the unit remains in standby  

  mode until 5 continuous steps are registered. Only then are the  

  5 steps calculated in, and an Active indicator “▲” appears on  

  the upper left of display.
2. When regular walk/run movement stops, after 2 seconds the  

  timer pauses and the unit switches to standby status (Active  

  indicator “▲” disappears).