Arcam A38 Handbook

Download Handbook of Arcam A38 Amplifier for Free or View it Online on All-Guides.com.

Brand: Arcam

Category: Amplifier

Type: Handbook

Model: Arcam A38 , Arcam P38

Pages: 18 (0.76 Mb)

Download Arcam A38 Handbook

Arcam A38 Handbook - Page 1
1
Arcam A38 Handbook - Page 2
2
Arcam A38 Handbook - Page 3
3
Arcam A38 Handbook - Page 4
4
Arcam A38 Handbook - Page 5
5
Arcam A38 Handbook - Page 6
6
Arcam A38 Handbook - Page 7
7
Arcam A38 Handbook - Page 8
8
Arcam A38 Handbook - Page 9
9
Arcam A38 Handbook - Page 10
10
Arcam A38 Handbook - Page 11
11
Arcam A38 Handbook - Page 12
12
Arcam A38 Handbook - Page 13
13
Arcam A38 Handbook - Page 14
14
Arcam A38 Handbook - Page 15
15
Arcam A38 Handbook - Page 16
16
Arcam A38 Handbook - Page 17
17
Arcam A38 Handbook - Page 18
18
E-11
English
Adjusting listening settings
e A38 allows you to customise various features of the
amplier to t your system. Use this diagram to help you
navigate through the available conguration options.
In the diagram, the control knob is shown as
.
Normally, the display shows the current volume and the
control knob is used to adjust this.
Press
MENU once to enter the setup menu, then press
OK repeatedly to cycle through the menu items. When
A38 setup
you have found the setting that you wish to adjust (as
shown on the front panel display), you can change the
setting using the control knob. Press MENU to store the
change and return to volume display mode – or press
OK again to move to the next setting.
Note that the menu will time-out aer a short period
without pressing a button, with the display reverting to
the current volume.
e following items can be adjusted from the setup
menu:
Conguring your A38 amplier
Balance
is allows you to adjust the output balance between le and right channels. e display is
also available directly by pressing the front panel DISPLAY button.
Volume resolution
ere are three volume-display options to chose from: ‘Standard, ‘Fine’ or ‘Reference.
Standard and Fine represent dierent levels of volume-control sensitivity; the Reference
setting gives absolute increments in 0.5dB steps.
Input trims
Input trims are used to compensate for variations in output levels of dierent source
equipment. If, for example, your CD player is louder at a given volume display value
than other inputs, you can attenuate it by using this setting so that it matches your other
components.
Use the source-select buttons to select the input you wish to adjust, then the control knob
to set (increase or decrease) the input volume for that source.
Max on volume
is can be used to limit the maximum volume the amplier operates at when it is rst
switched on: the A38 comes on at the (reduced) ‘Max. On Volume’ level if the last-used
volume exceeds this value.
If this item is set to ‘Disabled, the A38 always comes on at the last used volume, even if this
is very loud.
Processor mode
Processor mode enables you to x the gain (volume setting) of your A38. e A38 (in
combination with a power amp.) can then be used to drive the front le and right speakers
of a surround-sound system, when fed from a separate processor. e volume of the entire
system can then be controlled using the processor.
Feed the sound from the processor into the
AV input, then set the gain of the A38 to match
the ampliers that drive your other loudspeakers.
Reset
Conrming ‘Yes’ restores all amplier settings to their factory defaults.
‘Power On’ state