Arcam A38 Handbook

Download Handbook of Arcam A38 Amplifier for Free or View it Online on All-Guides.com.

Brand: Arcam

Category: Amplifier

Type: Handbook

Model: Arcam A38 , Arcam P38

Pages: 18 (0.76 Mb)

Download Arcam A38 Handbook

Arcam A38 Handbook - Page 1
1
Arcam A38 Handbook - Page 2
2
Arcam A38 Handbook - Page 3
3
Arcam A38 Handbook - Page 4
4
Arcam A38 Handbook - Page 5
5
Arcam A38 Handbook - Page 6
6
Arcam A38 Handbook - Page 7
7
Arcam A38 Handbook - Page 8
8
Arcam A38 Handbook - Page 9
9
Arcam A38 Handbook - Page 10
10
Arcam A38 Handbook - Page 11
11
Arcam A38 Handbook - Page 12
12
Arcam A38 Handbook - Page 13
13
Arcam A38 Handbook - Page 14
14
Arcam A38 Handbook - Page 15
15
Arcam A38 Handbook - Page 16
16
Arcam A38 Handbook - Page 17
17
Arcam A38 Handbook - Page 18
18
E-5
English
Placing the unit
< Place the amplier on a level, rm surface,
avoiding direct sunlight and sources of heat or
damp.
< Do not place the A38 on top of a power amplier
or other source of heat.
< Do not place the amplier in an enclosed space
such as a bookcase or closed cabinet unless there
is good provision for ventilation. e A38 and
P38 are designed to run warm during normal
operation.
< Do not place any other component or item on
top of the amplier as this may obstruct airow
around the heat-sink, causing the amplier to
run hot. (e unit placed on top of the amplier
would become hot, too.)
< Make sure the remote-control receiver to the
le of the front panel display is unobstructed,
otherwise this will impair the use of the remote-
control. If line-of-sight is impractical, a remote-
control repeater can be used with the rear panel
connector (see page 7).
< Do not place your record deck on top of this
unit. Record decks are very sensitive to the noise
generated by mains power supplies which will be
heard as a background ‘hum’ if the record deck is
too close.
Power
e amplier is supplied with a moulded mains plug
already tted to the lead. Check that the plug supplied
ts your supply – should you require a new mains lead,
please contact your Arcam dealer.
If your mains supply voltage or mains plug is dierent,
please contact your Arcam dealer immediately
Push the IEC plug end of the power cable into the
socket on the back of the amplier, making sure that it
is pushed in rmly. Plug the other end of the cable into
your mains socket and, if necessary, switch the socket
on.
Stand-by power
For remote stand-by operation, the ampliers control
power-supply is kept powered on all the time the unit is
connected to the mains supply. e front-panel power-
switch powers all other circuitry down and power
consumption in this mode is less than 2W.
is means that even though the power-switch is o, it
may be possible to hear a slight residual hum coming
from the mains transformer inside the amplier. is
is perfectly normal. However, if the unit is to be le
unused for an extended period, we recommend that you
disconnect it from the mains supply.
Interconnect cables
We recommend the use of high-quality screened cables
that are designed for the particular application. Other
cables will have dierent impedance characteristics
that will degrade the performance of your system (for
example, do not use cabling intended for video use to
carry audio signals). All cables should be kept as short
as is practically possible.
It is good practice when connecting your equipment to
make sure that the mains power-supply cabling is kept
as far away as possible from your audio cables. Failure to
do so may result in unwanted noise in the audio signals.