Smeg A11A-6 Instruction Manual

Download Instruction manual of Smeg A11A-6 Cooktop for Free or View it Online on All-Guides.com.

Brand: Smeg

Category: Cooktop

Type: Instruction manual for Smeg A11A-6

Pages: 32 (2.37 Mb)

Download Smeg A11A-6 Instruction manual

Smeg A11A-6 Instruction manual - Page 1
1
Smeg A11A-6 Instruction manual - Page 2
2
Smeg A11A-6 Instruction manual - Page 3
3
Smeg A11A-6 Instruction manual - Page 4
4
Smeg A11A-6 Instruction manual - Page 5
5
Smeg A11A-6 Instruction manual - Page 6
6
Smeg A11A-6 Instruction manual - Page 7
7
Smeg A11A-6 Instruction manual - Page 8
8
Smeg A11A-6 Instruction manual - Page 9
9
Smeg A11A-6 Instruction manual - Page 10
10
Smeg A11A-6 Instruction manual - Page 11
11
Smeg A11A-6 Instruction manual - Page 12
12
Smeg A11A-6 Instruction manual - Page 13
13
Smeg A11A-6 Instruction manual - Page 14
14
Smeg A11A-6 Instruction manual - Page 15
15
Smeg A11A-6 Instruction manual - Page 16
16
Smeg A11A-6 Instruction manual - Page 17
17
Smeg A11A-6 Instruction manual - Page 18
18
Smeg A11A-6 Instruction manual - Page 19
19
Smeg A11A-6 Instruction manual - Page 20
20
Smeg A11A-6 Instruction manual - Page 21
21
Smeg A11A-6 Instruction manual - Page 22
22
Smeg A11A-6 Instruction manual - Page 23
23
Smeg A11A-6 Instruction manual - Page 24
24
Smeg A11A-6 Instruction manual - Page 25
25
Smeg A11A-6 Instruction manual - Page 26
26
Smeg A11A-6 Instruction manual - Page 27
27
Smeg A11A-6 Instruction manual - Page 28
28
Smeg A11A-6 Instruction manual - Page 29
29
Smeg A11A-6 Instruction manual - Page 30
30
Smeg A11A-6 Instruction manual - Page 31
31
Smeg A11A-6 Instruction manual - Page 32
32
Instructions for the installer
2.2 Gas connection
This appliance is suitable for installation with Natural
Gas or LPG (propane). Refer to page 12 for the relevant
burner pressure and appropriate injector sizes. When
the appliance is to be connected to Natural Gas then the
pressure regulator supplied must be fitted to the gas
inlet. A test point (for checking the gas pressure) is
supplied either with the regulator or as a separate fitting
in the case of LPG (propane) appliances.
Connection of the appliance to the gas supply must be in
accordance with the requirements of AS5601. A ½” BSP
connector at the inlet is recommended and the gas
supply line to the appliance must be of adequate length
to allow sufficient withdrawal of appliance for service or
disconnection and be:
1. annealed copper pipe or;
2. flexible hose according to AS/NZ1869 & be at least Class “B”, 10 mm
diameter.
The appliance must be installed with provision to allow the gas to be
turned off and disconnected for servicing and removal of the appliance as
required from the gas supply.
Before the appliance is operated make certain all relevant parts are placed
in the correct position.
When the installation is completed the installation connections of
appliance will require to be leak tested, the burner operating pressure and
flame checked and adjusted.
Warranty service calls do not cover these adjustments!
To check the operating pressure of the appliance it is recommended at
least 2 large size burners are used. Ensure appliance is secured to wall
when installation is completed.
N.G. The regulator supplied must be fitted to the ½ BSP thread at the rear
of the appliance. An approved manual shut-off valve must be installed.
The N.G. regulator must be checked and adjusted to 1.0kPa after
installation.
ULPG: Can be connected to the inlet fitting
directly. The pressure must be checked to
ensure it is operating at 2.75kPa. A separate
test point fitting must be installed between the
piping & the appliance for the pressure to be
checked to ensure it is operating at 2.75kPa.
7