Smeg AP64S3 Instructions For Use Manual

Download User manual manual of OPTICOM VDC10X - DATA 2 Cooktop, Hob for Free or View it Online on All-Guides.com. This version of OPTICOM VDC10X - DATA 2 Manual compatible with such list of devices, as: VDC10X - DATA 2, HB64ABE3, SE63SEB3, SE64SEB3, SR804POGH

OPTICOM VDC10X -  DATA 2 User	manual	manual - Page 1
1
OPTICOM VDC10X -  DATA 2 User	manual	manual - Page 2
2
OPTICOM VDC10X -  DATA 2 User	manual	manual - Page 3
3
OPTICOM VDC10X -  DATA 2 User	manual	manual - Page 4
4
OPTICOM VDC10X -  DATA 2 User	manual	manual - Page 5
5
OPTICOM VDC10X -  DATA 2 User	manual	manual - Page 6
6
OPTICOM VDC10X -  DATA 2 User	manual	manual - Page 7
7
OPTICOM VDC10X -  DATA 2 User	manual	manual - Page 8
8
OPTICOM VDC10X -  DATA 2 User	manual	manual - Page 9
9
OPTICOM VDC10X -  DATA 2 User	manual	manual - Page 10
10
OPTICOM VDC10X -  DATA 2 User	manual	manual - Page 11
11
OPTICOM VDC10X -  DATA 2 User	manual	manual - Page 12
12
OPTICOM VDC10X -  DATA 2 User	manual	manual - Page 13
13
OPTICOM VDC10X -  DATA 2 User	manual	manual - Page 14
14
OPTICOM VDC10X -  DATA 2 User	manual	manual - Page 15
15
OPTICOM VDC10X -  DATA 2 User	manual	manual - Page 16
16
OPTICOM VDC10X -  DATA 2 User	manual	manual - Page 17
17
OPTICOM VDC10X -  DATA 2 User	manual	manual - Page 18
18
OPTICOM VDC10X -  DATA 2 User	manual	manual - Page 19
19
OPTICOM VDC10X -  DATA 2 User	manual	manual - Page 20
20
OPTICOM VDC10X -  DATA 2 User	manual	manual - Page 21
21
OPTICOM VDC10X -  DATA 2 User	manual	manual - Page 22
22
OPTICOM VDC10X -  DATA 2 User	manual	manual - Page 23
23
Instructions for the installer
35
5 ELECTRICAL CONNECTION
Make sure that the voltage and capacity of the power line conform to
the data shown on the plate located under the casing. Do not remove
this plate for any reason.
The plug on the end of the supply cable and the wall socket must be
the same type and conform to the current electrical system regulations.
Check that the power line is adequately grounded.
On the power line, install an omnipolar cut-off device with contact cut-
off distance greater than or equal to 3 mm, located in an easily
accessible position near the unit.
Do not use reducers, adapters or shunts.
If the power cable is replaced, the wire section on the new cable must
not be less than 1 mm
2
(3 x 1 cable), keeping in mind that the end to
be connected to the hob must have the ground wire (yellow-green)
longer by at least 20 mm. Use only H05V2V2-F cable or similar which
has a maximum temperature of 90°C. Any replacement needed should
be carried out by a specialised technician who should make the mains
connections according to the following diagram.
L = brown
N = blue
= yellow-green
The manufacturer will not be liable for any damage to persons or
property caused by non-observance of the above instructions or
deriving from the tampering of even a single part of the hob.