SMEG SDP20 Manual

Download Manual  of Smeg SDP20 Remote Control for Free or View it Online on All-Guides.com.

Brand: Smeg

Category: Remote Control

Type: Manual  for Smeg SDP20

Pages: 22 (1.67 Mb)

Download Smeg SDP20 Manual 

Smeg SDP20 Manual  - Page 1
1
Smeg SDP20 Manual  - Page 2
2
Smeg SDP20 Manual  - Page 3
3
Smeg SDP20 Manual  - Page 4
4
Smeg SDP20 Manual  - Page 5
5
Smeg SDP20 Manual  - Page 6
6
Smeg SDP20 Manual  - Page 7
7
Smeg SDP20 Manual  - Page 8
8
Smeg SDP20 Manual  - Page 9
9
Smeg SDP20 Manual  - Page 10
10
Smeg SDP20 Manual  - Page 11
11
Smeg SDP20 Manual  - Page 12
12
Smeg SDP20 Manual  - Page 13
13
Smeg SDP20 Manual  - Page 14
14
Smeg SDP20 Manual  - Page 15
15
Smeg SDP20 Manual  - Page 16
16
Smeg SDP20 Manual  - Page 17
17
Smeg SDP20 Manual  - Page 18
18
Smeg SDP20 Manual  - Page 19
19
Smeg SDP20 Manual  - Page 20
20
Smeg SDP20 Manual  - Page 21
21
Smeg SDP20 Manual  - Page 22
22
Using the Home Garden
41
10.USING THE HOME GARDEN
At first switch-on, the circuit board automatically presets for the use of program . The symbol
flashes to indicate that the time must be set on the control circuit board. For instructions on this
procedure, see point "9.6 Clock display/setting key".
WARNING: THE HOME GARDEN CAN ONLY BE OPERATED WITH THE REMOTE CONTROL.
THE CONTROL PANEL ON THE FRONT OF THE APPLIANCE IS PURELY AESTHETIC AND DOES
NOT OPERATE THE HOME GARDEN.
10.1 Removing and placing the pots in the Home Garden
To remove the pots from the appliance, proceed as follows:
Lift the appliance’s two side panels by their handles. The panels are mounted on sliding supports and
should be lifted gently to their maximum extension by simply pulling upwards. At this point, with both side
panels raised, the two sliding trays on which the pots are located can be pulled out. Take care not to exert
excessive force: the end stop which prevents them from falling may be damaged by this. Once the two
sliding trays are fully extended, the pots are available for use.
To refit them inside the Home Garden, simply repeat the same operations in reverse order.
WARNING: DIFFERENT POTS FROM THOSE SUPPLIED WITH THE HOME GARDEN MAY NOT BE
SUITABLE FOR GROWING YOUR PLANTS IN THE APPLIANCE
WARNING: THE HOME GARDEN IS CONSTRUCTED LARGELY OF GLASS. PROCEED GENTLY
AND WITH CARE WHEN HANDLING.
10.2 Automatic regulation of the internal micro-climate
The Home Garden is equipped with three sensors (humidity, light and temperature) which allow its
circuitry to control its environmental variables in accordance with the selected program.
There are three programs for the various types of plant you may wish to grow in the appliance.
The following table explains the types of plants which each program is intended to work with.
PROGRAM PLANTS OPERATING PARAMETERS
1 Green plants (decorative,
indoors), indoors bonsai,
cuttings and orchids.
- High humidity.
- Automatic heating when the external temp-pera-
ture is lower than 18°C.
- In case of insufficient external light, the appli-
ance’s lights stay on from 7:00 to 20:00.
- Low ventilation frequency.
2 Succulents. (eg. Cacti) - Low humidity.
- Automatic heating when the external
temperature is lower than 20°C.
- In case of insufficient external light, the appli-
ance’s lights stay on from 7:00 to 21:00.
- High ventilation frequency.
3 Flowering plants
and seedlings.
- Moderate humidity.
- Automatic heating when the external temp-pera-
ture is lower than 18°C.
- In case of insufficient external light, the appli-
ance’s lights stay on from 7:00 to 20:00.
- Average ventilation frequency.
CHECK THAT THE SELECTED PROGRAM IS SUITABLE FOR THE PLANTS YOU INTEND TO
GROW, WHICH MUST OBVIOUSLY ALL BE OF THE SAME TYPE.
IF, FOR EXAMPLE, YOU DECIDE TO REPLACE YOUR SUCCULENTS WITH GREEN PLANTS, YOU
MUST CHANGE FROM PROGRAM 2 TO PROGRAM 1 AS DESCRIBED ABOVE.