SMEG SDP20UL Manual

Download Manual  of Smeg SDP20UL Remote Control for Free or View it Online on All-Guides.com.

Brand: Smeg

Category: Remote Control

Type: Manual  for Smeg SDP20UL

Pages: 22 (4.94 Mb)

Download Smeg SDP20UL Manual 

Smeg SDP20UL Manual  - Page 1
1
Smeg SDP20UL Manual  - Page 2
2
Smeg SDP20UL Manual  - Page 3
3
Smeg SDP20UL Manual  - Page 4
4
Smeg SDP20UL Manual  - Page 5
5
Smeg SDP20UL Manual  - Page 6
6
Smeg SDP20UL Manual  - Page 7
7
Smeg SDP20UL Manual  - Page 8
8
Smeg SDP20UL Manual  - Page 9
9
Smeg SDP20UL Manual  - Page 10
10
Smeg SDP20UL Manual  - Page 11
11
Smeg SDP20UL Manual  - Page 12
12
Smeg SDP20UL Manual  - Page 13
13
Smeg SDP20UL Manual  - Page 14
14
Smeg SDP20UL Manual  - Page 15
15
Smeg SDP20UL Manual  - Page 16
16
Smeg SDP20UL Manual  - Page 17
17
Smeg SDP20UL Manual  - Page 18
18
Smeg SDP20UL Manual  - Page 19
19
Smeg SDP20UL Manual  - Page 20
20
Smeg SDP20UL Manual  - Page 21
21
Smeg SDP20UL Manual  - Page 22
22
Using the Home Garden
21
10.3 Selecting the program
When first switched on or when the
key is pressed, the Home Garden is in standby, as indicated by the
dot in the left hand temperature display (see point
, page
16). To activate automatic operation, simply point
the remote control at the appliance and press the key.
Once automatic operation has been activated, the appliance’s circuitry will run a check of the displays and all
control panel leds will light up.
Once this check has terminated, the system will ask you to select one of the 4 programs available
.
The symbol (followed by a number from 1 to 4) will flash on the left-hand display (the orange one). Use the
and keys to scroll through the 4 programs ( ; ; ; ). To choose the type of program,
see Section "10.2 Automatic regulation of the internal micro-climate".
If a program symbol appears on the display for more than 5 seconds, the respective program will activate.
This procedure shows how to select a program starting from standby.
Once the program has been selected, the appliance’s circuitry will ask you to set the time as described in
paragraph "9.6 Clock display/setting key".
TO CHANGE THE PROGRAM DURING NORMAL OPERATION, PROCEED AS FOLLOWS.
PRESS THE KEY ONCE: THE CURRENT PROGRAM WILL DISPLAY ON THE ORANGE
DISPLAY FOR A FEW SECONDS. NOW HOLD DOWN THE SAME KEY FOR THREE SECONDS;
THIS RETURNS TO THE PROGRAM SELECTION PROCEDURE AND A NEW PROGRAM CAN BE
SELECTED IN THE WAY DESCRIBED IN THE FIRST PART OF THIS PARAGRAPH.
THE HOME GARDEN AUTOMATICALLY REGULATES THE TEMPERATURE, HUMIDITY AND
LIGHTING, BUT IT SHOULD BE RECALLED THAT EVEN IN THESE OPTIMAL CONDITIONS, THE
PLANTS NEED FRESH AIR.
10.4 Manual Program
The Home Garden has a “manual” program in which the operating parameters (temperature and
humidity) can be modified.
To do this, select program (as described in point "10.3 Selecting the program"). To modify the
preset programs keep the key depressed for a few seconds if you wish to modify the humidity value,
or the key if you wish to modify the temperature value. In this modification mode, the display of the
value being changed will flash.
The parameters can be modified using the and keys.
5 seconds after the last key is pressed, the displays stop flashing and the values set are saved.
Pressing the and keys quickly once activates the "vaporizer" and "cuttings" functions as already
described.
The manual control program allows the user to set a number of parameters which control the
microclimate inside the Home Garden.
However, it must be remembered that whether these parameters are actually reached and maintained
over time they depend on the external environment surrounding the Home Garden. The heating
elements inside the Home Garden are located underneath the pots on the bottom level (as shown in Fig.
7 on page 14) and heat both the soil and the air.
Because of this dual action, to prevent damage to the plants inside the Home Garden it is important
always to set an internal temperature not much higher than the surrounding room temperature. To
reduce overheating risks, the Home Garden never heats to a temperature more than 4-5°C - 39-41°F
higher than the room temperature.
The maximum temperature that can be set with the manual program is 25 °C - 77° F
The maximum humidity that can be set with the manual program is 90%. To prevent overheating of
the ultrasound nebulizer, the Home Garden operates it in on/off mode. Therefore, whether or not the
preset humidity level is reached it depends on the humidity of the Home Garden's external environment
and the nebulizer cycle selected.