SMEG L23CL Installation And User Instructions Manual
Download Installation and user instructions manual of Smeg L23CL Indoor Fireplace, Telephone for Free or View it Online on All-Guides.com. This version of Smeg L23CL Manual compatible with such list of devices, as: L23LIN, L23LINP, L30FABBL, L30FABBLP, L30FABCR
Brand: Smeg
Category: Indoor Fireplace , Telephone
Type: Installation and user instructions manual
Model: Smeg L23CL , Smeg L23LIN , Smeg P23CL , Smeg P23LIN , Smeg L23CLP , Smeg L23LINP , Smeg L30FABBL , Smeg L30FABBLP , Smeg L30FABCR , Smeg L30FABCRP , Smeg L30FABRE , Smeg L30FABREP , Smeg L30FABSI , Smeg L30FABSIP , Smeg P23CLP , Smeg P23LINP
Pages: 16 (0.44 Mb)
Download Smeg L23CL Installation and user instructions manual
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
If the appliance is to be mounted on the inner leaf of a conventional cavity brick wall, or a solid
wall, then the fibre wall plugs and fixing screws provided may be used. Depending on the condi-
tion of the wall it may be necessary to use additional fixings. In this situation, any additional fixings
and wallplugs should be of the same size and type as the ones provided.At the appropriate stage
of the installation, drill four holes using only a 6.5mm masonry bit to a depth of 39mm. Insert the
fibre wallplugs provided ensuring they are flush to the wall.
If the appliance is to be mounted on a dry lined wall or a timber framed
construction wall then efforts should be made to fix in at least two posi-
tions vertically, into one of the wooden studs, or supporting wooden
members of the wall using two of the fixing screws provided. If this is not
achievable then the wall should be strengthened using appropriate build-
ing materials.
If there is no alternative than
to rely on some plasterboard
fixings then special cavity
screw fixings or hollow wall
anchors will be required which
are not supplied with this
product.These should be con-
structed from metal and not plastic and of the design indicated in figure 2.
For further guidance for wall fixing in timber framed buildings, refer to the
current edition of IGE/UP/7.
Flat
Wall Fixing - All Models
To assist with fixing the appliance, a template is provided.The L23 model template
is shown for the purposes of example in figure 3.
Mark the positions shown as “Fixing points” on the wall.
If a concealed gas connection is to be made ensure the gas supply pipe is in it’s
final position and can enter the appliance in the correct position when the appli-
ance is hung on the wall.
Drill the wall as appropriate for the type of wall as previously described in this
section, and insert the chosen type of wall fixings. Insert the wall fixing screws into
the top wall plugs, taking care to leave the screws protruding approximately 5mm from the wall. Now hang the appliance onto
these screws through the two keyhole shaped holes in the upper brackets on the back panel of the appliance.
Insert the lower fixing screws into the lower wall plugs through the corresponding fixing holes in the lower part of the back panel.
Do not tighten fully.
Before tightening the wall mounting screws fully, at this stage it is recommended to check the horizontal alignment of the appli-
ance with a spirit level, as small adjustments can still be made if necessary. When this has been checked, tighten all four fixing
screws fully. To access the upper fixing screws insert a screwdriver through the round access holes in the front face of the out-
let grille (as shown in figure 5). These access holes are located in the same position on all models.
There are no imitation fuel bed components to install. The appliance features a ribbon
burner which is designed to produce a continuous band of flame over it’s length. The
burner should be visually inspected to ensure it is free from any foreign matter.
If it is necessary to clean or dust off the burner then the glass door should be removed
by removal of the four retaining screws. Re-fit the glass door after cleaning or inspection,
ensuring a good seal. The gap between the spark electrode and the pilot should be 3 -
5mm to produce a good spark. There should be no need to adjust this. If under any cir-
cumstances the piezo electric spark fails, the pilot cannot be lit manually.
Turn on and test the gas supply up to the fire for any leaks, in accordance with the current edition of BS6891.
5
7.0 FIXING THE APPLIANCE (CONTINUED)
Plasterboard alone is not consid-
ered to be a structural material.
It is not recommended to rely on
plasterboard fixings alone to sup-
port the weight of the appliance.
WARNING
Figure 3
Figure 4
7.1 CHECKING THE BURNER AND SPARK GAP
8.0 TESTING AND COMMISSIONING
Figure 5
Spark gap
Figure 2
© 2007 Smeg (UK) LTD