• Home
• Brands
• Grindmaster Manuals
• Grindmaster G23-2B
• Grindmaster G Series G23-2B User Manual

Grindmaster G Series G23-2B User Manual

Download Operator's manual of Grindmaster G23-2B Coffee Maker, Freezer for Free or View it Online on All-Guides.com. This version of Grindmaster G23-2B Manual compatible with such list of devices, as: G23-2B, G236-2B, MG Series MG23-2B, MG Series MG235-2B, MG Series MG236-2B

1

2

3

4

9

PUT ON BOWL SEAL AND SHAFT SEAL

• Moisten bowl seal (T) with water

and put back on

• Check for wear of bell shaped rubber

shaft seal (see below ) replace if needed

• Lubricate inside of bell shaped shaft

seal (X) with food grade lubricant. Put

back seal making sure flared side faces

the cylinder

10

PUT ON GEAR RING/AUGER ASSEMBLY

• Put gear ring/auger assembly (U)

back in position

• Secure parts in place by screwing on

the bolt (S) counterclockwise

11

PUT ON BOWL

• Lightly moisten rear inner part of bowl

with food grade lubricant

• Position bowl into place making sure

it has a tight hold on the bowl seal •

•

Be sure bowl corners fit on outside edge of the top tray piece. The

lid cover will not fit properly if the bowl is not correctly positioned.

12

SECURE BOWL WITH KNOBS

Keep bowl lifted until the hole in lower bowl

edge is aligned with hole in front panel then

tightly screw on the knobs (P) without exerting

excessive pressure to avoid cracking the bowl

13

REASSEMBLE DISPENSING VALVE

• Lubricate o-rings with food grade

lubricant and place o-rings on valve

• Place spring over valve stem

• While pushing up on valve, insert

metal bar on handle under hook on valve

• Slide valve back into position until it

completely snaps into place

• Reassemble the handle (B) with the rele-

vant pin (G ) (See #5).

14

REASSEMBLE MIXING ROD

• Reassemble mixing rod (O) so that

its gears are aligned with the lower

gear ring

• Insert front pin into position at

front of bowl

15

INSTALL DRIP TRAY

• Reinstall drip tray, (AA) making sure that

the condensation drainage tube (AB) is

reinserted into its correct fixed position

allowing it to drain into the tray

• Plug unit into appropriate power supply

16

SANITIZING UNIT

• Fill bowl with a mix of water and sanitizing solution

• Turn auger on for 10 minutes to sanitize all parts

• Turn off auger

• Drain bowl through dispensing valve

•

Unscrew two knobs and lower bowl to drain out remaining solution

• Clean tray underneath bowl and lubricate rear bowl seal

• Reattach bowl

• Screw knobs back on

• Disconnect lamp cover from power. With clean cloth wash

underside of lamp cover with warm water and mild detergent.

Allow to air dry and wipe with cloth that has been dipped in

sanitizing mixture

CAUTION: MAKE SURE LAMP COVER HAS BEEN DISCONNECTED FROM

POWER.

1

TURN OFF ALL SWITCHES, EMPTY BOWL

& UNPLUG UNIT

• Turn off refrigeration / and

/ freezing switches and empty the

bowls of their remaining product

• Turn off auger switches and power switch

• Unplug the unit

2

REMOVE MIXING ROD

Pull out the mixing rod (O) by

pushing it slightly backwards

to remove it from its position

3

REMOVE KNOBS SECURING BOWL -

DRAIN EXCESS PRODUCT

• Unscrew and remove the two knobs (P)

• Then lower the bowl to drain out

any remaining product through the

dispensing valve (l)

4

REMOVE BOWLS

Remove bowl by pulling it outwards,

lightly tapping the back of bowl so

it comes out of position or by applying

slight downward pressure to the top front

edge of the bowl.

5

REMOVE DISPENSING VALVE

• Remove the pin (G) and slide the

handle out from it’s seat.

• Simultaneously apply pressure to the

securing tabs, lift the dispensing valve

out of its position.

• Disassemble remaining valve assembly

parts

6

REMOVE O-RINGS FROM DISPENSING VALVE

• Pinch o-ring between thumb

and index finger

• Squeeze and push o-ring out

of the groove

• Roll o-ring out of the groove with

your other thumb

7

REMOVE MIXING UNIT PARTS & DRIP TRAY

• Unscrew bolt (S) clockwise

• Pull off auger and gear ring assembly (U)

• Remove bowl seal (T) and bell shaped shaft

seal (X)

• Remove drip tray by lifting up the front edge,

while lowering the rear edge and pulling

it towards you

8

CLEAN ALL PARTS

• Thoroughly clean all parts removed

above as well as the base (Y) and

evaporator (Z).

• Wash with warm water using

a mild dish detergent and rinse

thoroughly with clean water.

Allow to air dry.

CAUTION: DO NOT USE ABRASIVE CLEANERS OR SCRUB PADS.

ABRASIVES WILL SCRATCH PLASTIC PARTS AND OTHER FINISHES.

TO DISASSEMBLE TO RE-ASSEMBLE

G & MG & ID Series Granita Machines

Operators

Manual

B

K

O

P

O

S X

U

T

S

X U

T

O

AA

AB

I

S X

U

T

DAILY CARE & CLEANING INSTRUCTIONS:

For the machine to function properly, it is important that the cleaning procedures be carried out daily.