Sony WX-4500X Install Manual

Download Installation/connections of Sony WX-4500X - Changer Control Audio Master Car Receiver, Car Stereo System for Free or View it Online on All-Guides.com.

Sony WX-4500X - Changer Control Audio Master Installation/connections - Page 1
1
Sony WX-4500X - Changer Control Audio Master Installation/connections - Page 2
2
Sony WX-4500X - Changer Control Audio Master Installation/connections - Page 3
3
Sony WX-4500X - Changer Control Audio Master Installation/connections - Page 4
4
Sony WX-4500X - Changer Control Audio Master Installation/connections - Page 5
5
Sony Corporation © 2001 Printed in Japan
WX-4500X
Equipment used in illustrations (not supplied)
插圖中的裝置(非附送)
##<KR>##
Cautions
This unit is designed for negative ground 12 V
DC operation only.
Do not get the wires under a screw, or caught
in moving parts (e.g. seat railing).
Before making connections, turn the car
ignition off to avoid short circuits.
Connect the yellow and red power input leads
only after all other leads have been connected.
Run all ground wires to a common ground
point.
Be sure to insulate any loose unconnected
wires with electrical tape for safety.
The use of optical instruments with this
product will increase eye hazard.
Notes on the power supply cord (yellow)
When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
When no car circuits are rated high enough,
connect the unit directly to the battery.
Parts Iist (1)
The numbers in the list are keyed to those in the
instructions.
Connection example (2)
Tip (2-B-
)
For connecting two or more changers, the source
selector XA-C30 (optional) is necessary.
Connection diagram (3)
When insert the each connector, be sure to insert
it securely, as vibration through driving may
cause a poor connection.
1 To a metal surface of the car
First connect the black ground lead, then
connect the yellow and red power input leads.
2 To the power antenna control lead or power
supply lead of antenna booster amplifier
Notes
• It is not necessary to connect this lead if there
is no power antenna or antenna booster, or
with a manually-operated telescopic antenna.
• When your car has a built-in FM/AM antenna in
the rear/side glass, see “Notes on the control
and power supply leads.”
1
2
B
12
× 6
3
4
× 6
Power amplifier
功率放大器
##<KR>##
CD/MD changer
CD/MD 換碟機
##<KR>##
Front speaker
前揚聲器
##<KR>##
Rear speaker
後揚聲器
##<KR>##
Source selector*
音源選擇器*
##<KR>##*
BUS CONTROL IN
A
Installation/Connections
安裝線路連接
##<KR>##
Changer Control
Audio Master
3 To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
4 To the interface cable of a car telephone
5 To a car’s illumination feed
Be sure to connect the black ground lead to it
first.
6 To the +12 V power terminal which is energized
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energised at all times.
Be sure to connect the black ground lead to it
first.
• When your car has a built-in FM/AM antenna in
the rear/side glass, see “Notes on the control
and power supply leads.”
7 To the +12 V power terminal which is energised
at all times
Be sure to connect the black ground lead to it
first.
Notes on the control and power supply leads
• The power antenna control lead (blue) supplies
+12 V DC when you turn on the tuner.
• When your car has built-in FM/AM antenna in the
rear/side glass, connect the power antenna control
lead (blue) or the accessory power input lead (red)
to the power terminal of the existing antenna
booster. For details, consult your dealer.
• A power antenna without relay box cannot be
used with this unit.
Memory hold connection
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition key is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid its damage.
• Do not connect the speaker terminals to the car
chassis, or connect the terminals of the right
speakers with those of the left speaker.
• Do not connect the ground lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
• To avoid a malfunction, do not use the built-in
speaker wires installed in your car if the unit shares
a common negative (–) lead for the right and left
speakers.
• Do not connect the unit’s speaker cords to each
other.
Active subwoofer
##<CT>##
##<KR>##
Rotary commander RM-X4S
旋轉式控制器 RM-X4S
##<KR>##
SUBWOOFER OUT
(MONO)
*I-3-229-007-11*(1)
For NISSAN cars only
僅適用 NISSAN 日產牌汽車
##<KR>##
* not supplied
非附送
##<KR>##
BUS AUDIO IN
BUS CONTROL IN
BUS AUDIO IN