Sony XAV-701BT Installation Manual

Download Installation/connections of Sony XAV-701BT Car Receiver, Car Stereo System for Free or View it Online on All-Guides.com.

Brand: Sony

Category: Car Receiver , Car Stereo System , Car Video System

Type: Installation/connections

Model: Sony XAV-701BT , Sony XAV-741

Pages: 2 (0.35 Mb)

Download Sony XAV-701BT Installation/connections

Sony XAV-701BT Installation/connections - Page 1
1
Sony XAV-701BT Installation/connections - Page 2
2
Cautions

Run all ground (earth) leads to a common ground
(earth) point.

This unit is designed for negative ground (earth) 12 V
DC operation only.

Do not disassemble or modify the unit.

Do not install in locations which interfere with airbag
operation.

Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).

Before making connections, turn the car ignition off to
avoid short circuits.

Connect the yellow and red power supply leads only
after all other leads have been connected.

Be sure to insulate any loose unconnected leads with
electrical tape for safety.

Do not press on the LCD when installing the unit.

Install the unit with the monitor facing straight forward;
do not install it at a slanted angle.
Notes on the power supply lead (yellow)

When connecting this unit in combination with other
stereo components, the amperage rating of the car
circuit to which the unit is connected must be higher
than the sum of each component's fuse amperage rating.

If no car circuits are rated high enough, connect the unit
directly to the battery.
Parts list

The numbers in the list correspond to those in the
instructions.

The bracket is attached to the unit before shipping.
Before mounting the unit, use the release keys to
remove the bracket from the unit. For details, see
“Removing the bracket ()” on the reverse side of the
sheet.

Keep the release keys for future use as they are
also necessary if you remove the unit from your
car.

The screws and frames are attached to the unit
before shipping. For details, see “Adjusting the frames
()” on the reverse side.

For XAV-701BT only: Assemble the parts of the
microphone before use. For details, see “Installing the
microphone (XAV-701BT only) ()” on the reverse
side.
Caution
Handle the bracket carefully to avoid injuring your
fingers.
Catch
Note
Before installing, make sure that the catches on both sides of the bracket
are bent inwards 3.5 mm (
5
/32 in). If the catches are straight or bent
outwards, the unit will not be installed securely and may spring out.
Connection example
Notes (-
A
)

Be sure to connect the ground (earth) lead before connecting the
amplifier.

The alarm will only sound if the built-in amplifier is used.
Note (-
B
)
You cannot use multiple auxiliary devices simultaneously, even if they are
connected to different terminals.
Connection diagram

To a common ground (earth) point
First connect the black ground (earth) lead, then connect the yellow
and red power supply leads.

To the power antenna (aerial) control lead or the
power supply lead of the antenna (aerial) booster
Notes

It is not necessary to connect this lead if there is no power antenna
(aerial) or antenna (aerial) booster, or with a manually-operated
telescopic antenna (aerial).

If your car has a built-in FM/AM antenna (aerial) in the rear/side
glass, see “Notes on the control and power supply leads.
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting any other system
may damage the unit.

To a cars illumination signal
Be sure to first connect the black ground (earth) lead to a common
ground (earth) point.

To the +12 V power terminal which is energized
when the ignition switch is set to the accessory
position
Notes

If there is no accessory position, connect to the +12 V power
(battery) terminal which is energized at all times.
Be sure to first connect the black ground (earth) lead to a common
ground (earth) point.

If your car has a built-in FM/AM antenna (aerial) in the rear/side
glass, see “Notes on the control and power supply leads.

To the +12 V power terminal which is energized
at all times
Be sure to first connect the black ground (earth) lead to a common
ground (earth) point.

To the parking brake switch cord

To an auxiliary device such as a portable media
player, game console, etc. (not supplied)
Tip
You can use an RCA pin cord (not supplied) to connect auxiliary
devices.

To the +12 V power terminal of the car’s rear lamp
lead (only when connecting the rear view
camera)
Notes on the control and power supply leads

REM OUT lead (blue/white striped) supplies +12 V DC when you turn on
the unit.

If your car has built-in FM/AM antenna (aerial) in the rear/side glass,
connect REM OUT lead (blue/white striped) or the accessory power
supply lead (red) to the power terminal of the existing antenna (aerial)
booster. For details, consult your dealer.

A power antenna (aerial) without a relay box cannot be used with this
unit.
Memory hold connection
When the yellow power supply lead is connected, power will always be
supplied to the memory circuit even when the ignition switch is turned off.
Notes on speaker connection

Before connecting the speakers, turn the unit off.

Use speakers with an impedance of 4 to 8 ohms, and with adequate
power handling capacities to avoid damage.

Do not connect the speaker terminals to the car chassis, or connect the
terminals of the right speakers with those of the left speakers.

Do not connect the ground (earth) lead of this unit to the negative (–)
terminal of a speaker.

Do not attempt to connect the speakers in parallel.

Connect only passive speakers. Connecting active speakers (with
built-in amplifiers) to the speaker terminals may damage the unit.

To avoid a malfunction, do not use the built-in speaker leads installed in
your car if they feature a common negative (–) lead for the right and left
speakers.

Do not connect the unit’s speaker leads to each other.
Notes on connection

If “Output connection failure.” appears in the display, make sure the
speaker and amplifier are connected correctly.

To use the monitor for the rear seats, connect the parking brake switch
cord to the ground (earth).
FRONT AUDIO
OUT
SUB OUT
REAR OUT
Z×Z L
/
R
REAR AUDIO
OUT
AUX IN
(
VIDEO
)
AUX AUDIO
IN
CAMERA
*
not supplied
Video camera*
A
B
4-422-719-11 (1)
Installation/Connections
AV Center
XAV-701BT/XAV-741
Equipment used in illustrations (not supplied)
Subwoofer
Smartphone
b
c
Front speaker
iPod
Rear speaker
Rear view camera
Power amplifier
Monitor
a
*
1
Speaker impedance: 4 – 8 ohms × 4
*
2
The microphone is supplied with
XAV-701BT only. For details on installing
the microphone, see “Installing the
microphone (XAV-701BT only) ()” on
the reverse side.
*
3
The microphone input cord is available
on XAV-701BT only. Whether in use or
not, route the microphone input cord
such that it does not interfere with
driving. Secure the cord with a clamp,
etc., if it is installed around your feet.
*
4
RCA pin cord (not supplied)
*
5
For details on connecting to the parking
brake switch cord, see “Connecting the
parking brake lead (
)” on the reverse
side.
*
6
not supplied
*
7
The sound is output from this terminal
only when ZONE x ZONE is activated.
This terminal outputs a fixed level
regardless of the volume control of the
unit.
*
8
A separate adaptor may be required.
*
9
USB connection cable RC-202IPV (not
supplied). To connect an iPod via
RC-202IPV, make sure to connect the
video output plug to AUX1 IN.
MIC IN
*
3
AUX2 AUDIO
IN
Z×Z L
/
R
*
7
REVERSE IN
CAMERA
REAR OUT
REMOTE IN
*
8
SUB OUT
EXT
AUX1 AUDIO
IN
FRONT
AUDIO OUT
REAR
AUDIO OUT
AUX2 IN
AUX1 IN
Fuse (10 A)
From car antenna (aerial)
*
4
REM OUT
Max. supply current: 0.4 A
ILLUMINATION
*
5
PARKING BRAKE
Blue/white striped
White
Green
Purple
White/black striped
Gray/black striped
Green/black striped
Gray
Purple/black striped
Red
Yellow
Black Orange/white striped
Light green
*
2
*
4
*
6
*
9
*
4
*
4
*
4
*
4
(XAV-701BT only)
× 2
× 8
× 2
× 2
*
1
*
9
XAV-701BT
XAV-701BT only
Left
Right
Left
Right