Haier 0010515222 Operation Manual

Download Operation manual of Haier 0010515222 Air Conditioner for Free or View it Online on All-Guides.com. This version of Haier 0010515222 Manual compatible with such list of devices, as: 0010515222, 10515222, HSU-12CR03-Y, HSU-18CR03-Y, HSU-18CR03-Y - annexe 1

Haier 0010515222 Operation manual - Page 1
1
Haier 0010515222 Operation manual - Page 2
2
Haier 0010515222 Operation manual - Page 3
3
Haier 0010515222 Operation manual - Page 4
4
Haier 0010515222 Operation manual - Page 5
5
Haier 0010515222 Operation manual - Page 6
6
Haier 0010515222 Operation manual - Page 7
7
Haier 0010515222 Operation manual - Page 8
8
Haier 0010515222 Operation manual - Page 9
9
Haier 0010515222 Operation manual - Page 10
10
Haier 0010515222 Operation manual - Page 11
11
Haier 0010515222 Operation manual - Page 12
12
Haier 0010515222 Operation manual - Page 13
13
Haier 0010515222 Operation manual - Page 14
14
Haier 0010515222 Operation manual - Page 15
15
Haier 0010515222 Operation manual - Page 16
16
Haier 0010515222 Operation manual - Page 17
17
Haier 0010515222 Operation manual - Page 18
18
Haier 0010515222 Operation manual - Page 19
19
Haier 0010515222 Operation manual - Page 20
20
Haier 0010515222 Operation manual - Page 21
21
Haier 0010515222 Operation manual - Page 22
22
Haier 0010515222 Operation manual - Page 23
23
Haier 0010515222 Operation manual - Page 24
24
Haier 0010515222 Operation manual - Page 25
25
Haier 0010515222 Operation manual - Page 26
26
Haier 0010515222 Operation manual - Page 27
27
Haier 0010515222 Operation manual - Page 28
28
Remove the batteries in case unit won't be in usage for a long period. If there are any display
after taking-out, just need to press reset key.
Clock Set
When unit is started for the first time and after replacing batteries in
remote controller, clock should be adjusted as follows:
Remote controller's operation
3. After time setting is confirmed, press SET, "AM" or "PM" stop flashing,
while clock starts working.
2. Press or to set correct time. Each press will increase or decrease
1 min. If the button is kept depressed, time will change quickly.
1. Press CLOCK button,"AM" or "PM" flashes.
When in use, put the signal transmission head directly to the receiver hole on the indoor unit.
The distance between the signal transmission head and the receiver hole should be within
7m without any obstacle as well.
Don't throw or knock the remoter controller.
When electronic-started type fluorescent lamp or change-over type fluorescent lamp or
wireless telephone is installed in the room, the receiver is apt to be disturbed in receiving
the signals, so the distance to the indoor unit should be shorter.
Loading of the battery
Load the batteries as illustrated right
2 R-03 (7#) batteries
Remove the battery cover:
Slightly press" "area and push down the cover
as illustrated.
Load the battery:
Be sure that the loading is in line with the "+" / "-".
request as illustrated on the bottom of the case.
Put on the cover again.
Confirmation indicator:
After pressing power ON/OFF, if no display, reload the batteries.
Note:
Full display or unclear display during operation indicates the batteries have been used up.
Please change batteries.
Used two new same-typed batteries when loading.
If the remote controller can't run normally during operation, please remove the batteries and
reload several minutes later.
Hint:
Parts and Functions
POWER/SOFT
FRESH
7