Panasonic TY-LA1500 User Manual

Download Lamp replacement update of Panasonic TY-LA1500 TV Accessories for Free or View it Online on All-Guides.com.

Brand: Panasonic

Category: TV Accessories

Type: Lamp replacement update for Panasonic TY-LA1500

Pages: 2 (0.09 Mb)

Download Panasonic TY-LA1500 Lamp replacement update

Panasonic TY-LA1500 Lamp replacement update - Page 1
1
Panasonic TY-LA1500 Lamp replacement update - Page 2
2
WARNING:
The lamp may be hot. Be careful when handling.
CAUTION:
High-pressure lamp may explode if improperly
handled.
Danger of injury due to glass fragments.
Lamp replacement procedure
1Follow the “Turning the power on and off” steps.
After turning off the power, unplug the power cord
from the wall outlet and confirm that the area
around the lamp unit has cooled down.
Please wait more than one hour for lamp
replacement.
[ If you need to replace the lamp more
urgently ]
The Projection display has a forced cooling
feature. After the POWER button is turned OFF,
and during the first minute of the normal cooling
fan operation, press the VOL+ button on the
projection display and button on the remote
control at same time for more than 5 seconds.
The cooling fan operates for about 10 minutes.
The LAMP indicator flashes red 5 times every 5
seconds.
POWER button/POWER indicator
Lamp Replacement
3Remove the Lamp cover screws.
First read caution and warning labels on lamp
cover. Then, remove the lamp cover screws (2)
by using a screwdriver.
Lamp unit screws
Screwdriver
4Remove the lamp unit screws (2) with a
screwdriver. Then, grasp the lamp unit as shown
in the diagram, and slowly remove from the
projection display.
Do not drop, as the impact of dropping may
cause the lamp to explode.
2Remove the left Speaker cover.
Place your fingertips under the left speaker
panel and pull it from the projection display.
Lamp unit handle
Lamp cover handle
6Replace the Lamp unit and cover screws.
Replace the lamp unit/cover screws with a
screwdriver.
Properly dispose of old lamp.
Attach the lamp unit and lamp unit housing door
securely. If the lamp unit and lamp unit housing
door are not attached securely, the protective
circuit will be activated and the power will not
turn on.
Note
7Replace the left Speaker cover.
5Insert the new lamp unit being careful of the
insertion direction.
Press on the arrow mark making sure insertion
is done correctly.
The replacement lamp comes with an air filter.
When replacing the lamp, also replace the air
filter at the same time.
Air Filter Replacement
Note
For the procedure to clean the air filter,
please refer to the operating instructions.
Lamp time reset procedure
1 Be sure the power cord is plugged into a
properly grounded wall outlet. Then, press the
POWER button on the projection display or the
remote control to turn the power on.
Warning: Only perform lamp time reset when
the lamp has been replaced.
When lamp time reset is finished, the LAMP
indicator goes out.
Note
After lamp replacement,
follow the procedure below
3 When reset procedure
is complete, the
screen on the right will
appear.
and
Lamp cover screws
1Remove the Air Filter unit
Grasp the indented portion of the air filter and
pull it out of the projection display.
2 Replace the new Air Filter unit.
Slide the new air filter into the projection display
so that the indentations of the filter and
projection display are aligned. Then, press on
the arrow mark until you hear it snap into
place.
Indent
LAMP indicator
2 While pressing the VOL- button on the
projection display, hold down the PIP button
on the remote control at same time for more
than 5 seconds.
EXIT
EXIT
RECALL
RECALL
.0OTTESER
SAWEMITPMAL
LSQC0291
Air Filter replacement procedure
CAUTION:
[Under no circumstance should you touch the
actual bulb.]
At this high operating temperature the natural oil
on your finger can cause the glass to weaken
where touched and the bulb can crack or
explode.
This product has a High Intensity Discharge (HID)
lamp that contains a small amount of mercury.
Disposal of these materials may be regulated in
your community due to environmental
considerations.
For disposal or recycling information please contact
your local authorities, or the Electronics Industries
Alliance: <http://www.eiae.org.>
CAUTION:
Because of the possibility of injury, strictly follow
the replacement procedure below.