Haier 50FREE-3B User's Manual

Download Operation & user’s manual of Haier 50FREE-3B Washer for Free or View it Online on All-Guides.com.

Brand: Haier

Category: Washer

Type: Operation & user’s manual for Haier 50FREE-3B

Pages: 10 (1.26 Mb)

Download Haier 50FREE-3B Operation & user’s manual

Haier 50FREE-3B Operation & user’s manual - Page 1
1
Haier 50FREE-3B Operation & user’s manual - Page 2
2
Haier 50FREE-3B Operation & user’s manual - Page 3
3
Haier 50FREE-3B Operation & user’s manual - Page 4
4
Haier 50FREE-3B Operation & user’s manual - Page 5
5
Haier 50FREE-3B Operation & user’s manual - Page 6
6
Haier 50FREE-3B Operation & user’s manual - Page 7
7
Haier 50FREE-3B Operation & user’s manual - Page 8
8
Haier 50FREE-3B Operation & user’s manual - Page 9
9
Haier 50FREE-3B Operation & user’s manual - Page 10
10
Safety precautions
Please insert the power cord into special rece-
ptacle with rated voltage.If the power cord is
three-phase wire,please use three-phase rec-
eptacle.The earthing terminal of the receptacle
must be earthed reliably.If it is two-phase wire,
please guarantee that the earthing wire is ear-
thed reliably.If possible ,please adopt electric
leakage protector.
Do not damage the power cord,bend ,extend,twist,bind or alter it by force.Do not press or
nip it with weight.If the power cord or the power plug is bad, or the power plug becomes
flexible,to avoid risk it is required to have it replaced by the technicians of our special
shop or the costomer care agent. Keep the pin of the power plug clean,if the
power plug is polluted with dust,please wipe with dry cloth carefully.
The power cord plug should be convenient
to be pluged in or pluged out with hand
while the washing machine runs normally.
Be sure to pull the plug out and close the
water tap when the machine is idle,when
moving the machine,or when cleaning
the machine.Do not use wet hand to ins-
ert or pull out the power plug.
In case the washing machine is installed
on ground with carpet, do not block the
ventilation hole with carpet.
Do not let the machine share one receptacle
with other electric appliances. If the power
plug is damaged, or the plugging into the
receptacle is loose, do not use the plug any
more.
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations.
Do not use water hotter above 50 C .
Do not put the machine at damp place like
the bathroom. Never wash it with water.
Not put wet laundries on the control panel.
soft items
The ventilation holes
at the bottom
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time (
about 1 hour), then close the top lid.
4.Hang up the power cord and drain hose.
3.Be sure to pull off the power plug before maintenance.
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.
The filter screen of the water inlet valve is likely to be
blocked by foreign materials and influence the water
inlet.
Please clean it with brush every two months.
If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
Wipe it with neutral detergent.
Do not wipe it with thinner, petrol, alcohol etc.
After using, please clean the lint and foreign materials of the lint filter etc. in time. Otherwise it may influence
your using the machine.
Disposal after washing
Please first pull off the power plug from the receptacle before cleaning.
2
15
Figure 2
The back cover of lint filter
Install
Dismantle
Down
Up
Figure 1
Down
Dismantle
Install
Up
The front cover of lint filter
Lint filter:
The lint filter must be used during washing.
It must be cleaned in time after each using.
1.Push down the spring piece of the top lint filter to
make the claws out of the filter cover, and then
pull out the lint filter to get it down. figure1
2.Pull the back of the lint filter, and then you can get
down it off the front cover of the lint filter. figure2
3.Sweep the rubbish in the lint filter.
4.Put the back of the lint filter into the front cover .
5.Put the lint filter into filter cover, and make it tight .
6.Make sure the lint filter well installed, or it can
influence your use.