Haier HW60-B12866NZP User Manual
Download Operating instructions of Haier HW60-B12866NZP Washer for Free or View it Online on All-Guides.com.
Brand: Haier
Category: Washer
Type: Operating instructions for Haier HW60-B12866NZP
Pages: 2 (5.27 Mb)
1
2
Power
Automatic Drum Washer
Operating Instructions
Models:
Please read this manual carefully before use.
Please keep this manual in a safe place for future
reference.
Specifications
This product is classified as
Class I appliance. Please pay
attention to electrical safety
during use.
The diagrams in this manual are
for illustrative purpose only. In
consideration of continuous
product improvement, please
see the actual product for the
appearance, color and
accessories which may be
inconsistent with those
described in this manual. We
hereby apologize for this.
Contents
1. Notice before Use
2. Safety Precautions
3. Precautions for Use
4. Preparations before Washing
5. Operational Procedure
6. Control Panel and Program Description
7. Display Screen Description
8. Other Functions
9. Fault Clearance
10. Cleaning/Maintenance
Technology of
variable frequency drive
Technology of
power-down memory
Technology of
automatic selection
1. Notice before Use
Please install and adjust the washer according to the instructions in this
manual so that you can use it in a correct and safer manner.
To connect the water inlet pipe
1. Select a proper water tap
2. Remove the water inlet pipe joint
The length of front end must be more than 10mm. If the
end face of water tap outlet is unsmooth, please file it
smooth to avoid water leakage.
① Press the lower end of locking lever;
② Hold the water inlet pipe, press
down the slider and remove the water
inlet pipe joint;
4. Connect the water inlet pipe
① Press down the slider and insert the
water pipe into the water inlet pipe joint;
② Hook the water inlet pipe joint with
the locking lever, then loosen the slider
until a “poop” is heard.
5. Connect to the washer
① Ring the nut at the other end of water
inlet pipe onto the water inlet valve joint;
② Tighten and confirm the nut of water
inlet pipe in place.
6. Check the water inlet pipe for good connection
① Check for firm connection;
② After installation, turn on the water tap and
check for water leakage;
③ Before every use of the washer, please check
for firm connection between the water inlet pipe
and the water tap;
④ Never forcibly bend the water inlet pipe.
Installation of the rat guard
Drain pipe
The outlet end of drain pipe must be
higher than 80cm and the highest point
must be less than 100cm. To prevent the
drain pipe from coming off, you may
secure it to its clamp at the back of washer
or to the firm holder as shown in the
figure.
It is not recommended to extend the drain
pipe. If the extension pipe exceeds 2.5m
in length, simultaneous water feeding and
drainage is likely to occur. Please contact
our After-sales Service Department for the
extension of drain pipe.
Adjustment of the feet
Be sure to adjust four feet
to level the washer before
use.
3. Install the water inlet pipe joint
① Loosen the nut to the extent that
approximate 3-4 turns of screw thread are
exposed;
② Loosen four screws of the water inlet pipe
joint to the extent that the joint can be ringed
onto the water tap;
③ If the water inlet pipe joint cannot be ringed
onto the water tap, please remove the bushing
and install again;
④ Turn one of screws to an approximately
proper position in advance, ring the water inlet
pipe joint onto the water tap, then evenly
tighten the remaining three screws in place,
and finally tighten the nut.
Water inlet pipe joint
Locking lever
Slider
Water inlet pipe
Wall
If the water tap is
placed against the wall,
you may turn this screw
to a proper position in
advance.
Bushing
3-4 turns
Tally
Nut
Locking lever
fig. 1 fig. 2
Note:
After finishing the adjustment of
four feet, turn the foot support
nuts to cling to the shell in order
to support the washer.
Distributor boxes
(Add a proper amount of
detergent required by washing)
Pre-wash detergent box
Main wash detergent box
Softener and bleach box
When selecting the pre-wash function or the pre-wash
program, add detergent into the pre-wash box to pre-wash
the clothes;
As for the dosage of detergent, please refer to the
instructions for detergent. Excessive detergent may result
in too many bubbles and spill as well as affect its
dissolution. Special low foaming detergent for drum
washers shall be used. When washing synthetic or wool
fabrics, be sure to use special detergent;
The level of softener or liquid detergent should not be
higher than the “MAX” mark of a distributor box.
Concentrated softener or liquid detergent should be diluted
before being added into a distributor box.
Table top
Drain pipe holder
Main control
panel
Front panel
Inner drum
Window pad
Door
Sight glass
Foot
Lower trim
Filter door
Table top
Water inlet valve
Power cord
Screw (4 pcs)
Power plug
Back cover plate
Drain pipe clamp
Drain pipe
Splash-proof plastic
plug (4 pcs)
Shell
Packaging bolts and accessories
Packaging bolts and accessories are used to
fix internal components of the washer during
transport and should be removed before using
the washer.
Unscrew packaging bolts and take
out the back-up block.
Block the bolt hole with a
splash-proof plastic plug.
Please keep such disassembled components
as packaging bolt and back-up block in a safe
place for future handling of the washer.
Accessories
Water inlet pipe assy
Drain pipe holder
Rat guard
Operating
instructions
2. Safety Precautions 3. Precautions for Use 4. Preparations
Electrical safety
prompt:
Please pay attention to
electrical safety when
using the washer.
Warning sign: The
contents with this
sign involve the
safety of both the
product and user. Be
sure to strictly follow
these instructions,
otherwise the washer
may be damaged or
the user may be
injured.
Prohibitory sign: The
contents with this
sign indicate the
behaviors to be
absolutely prohibited.
Failure to follow these
instructions may
result in damage to
the washer or
personal injury.
1. The plug should be accessible after the washer is
installed in place. Do not disconnect the plug from the
socket by pulling the power cord. If the power cord needs to
be replaced, ask a qualified person or contact our
After-sales Service Department for replacement. Prevent
the power cord from being pressed by any foot and from
such problems as break-off, flattening, etc.
2. Power supply must use a separate socket, the grounding
terminal of which must be reliably grounded.
3. Such overload protective devices as proper fuse must be available at the user’s home.
And, the ammeter, wires and socket must be able to withstand the current of 10A.
1. Keep the washer away from any heat source and direct sunlight to prevent aging of plastic/rubber
parts.
1. Do not use such chemicals as flammable detergent and dry-cleaning
solvent to wash the clothes. Do not use any organic solvent or corrosive
liquid to wipe the exterior and rubber parts of the washer. Do not use any
flammable spray near the washer. In case of flammable gas leakage, do
not plug in or unplug the washer. Do not use the washer near the
environment with flammable and explosive gas or liquid such as biomass
pool, etc.
2. The washer’s door is relatively hot during heating. For the purpose of safety, keep
children away from the washer. In addition, when draining hot water, be careful to avoid
scald.
3. After unpacking the washer, do not allow children to play with the disassembled
packaging materials such as carton, plastic packaging bag and foam, etc.
4. Do not install the washer outdoors and in excessively humid environment, otherwise
the moisture on electrical components may easily cause damage to the ignition system
or other accidents. In case of inadvertent water spray onto or into the washer, only after
the washer thoroughly dries can you use it.
5. Neither place the washer directly on airproof carpet to prevent its bottom vent from
being blocked nor close up to a wall or furniture to avoid accidents. Do not use the
washer on any platform higher than the floor
, otherwise it may fall off onto the floor and
be damaged.
1. Due to fluctuation of water pressure, please check all the joints of water inlet pipe, water tap and
drain pipe for firm connection before washing every time. In case of loose water pipe connection or
water leakage, please turn off the water tap and take proper measures or contact our After-sales
Service Department for reconnection. Only after such faults are cleared can you use it again.
2. Using the washer at 0 ℃ and below may damage the water inlet valve and drainage system. If the
washer is stored at 0 ℃ and below, be sure to move and leave it in the environment at room
temperature for 2-4 hours before use.
3. It is recommended that the washer be installed in a location with floor drainer.
4. Do not place any heavy object, heat-producing appliance and item liable to water/liquid leakage to
avoid the deformation of table top and plastic parts.
5. Do not wash such waterproof articles as raincoat, bicycle cover and down products as well as
carpet to avoid abnormal vibration or the damage to articles.
6. If a brassiere with steel wire is washed in the washer, the steel wire may bounce out. Therefore, do
not wash any brassiere with steel wire in order to protect the washer.
7. Do not put the clothes tainted with chemicals into the washer.
8. Do not open any detergent distributor box during the program operation to avoid some detergent
leaving in the box.
9. The washer’s door is equipped with self-lock safety device. Only when the washer is in safe state
(the water level is below the lower edge of sight glass, the temperature inside the drum is below 50 ℃ ,
the inner drum is not rotating) can you unlock the door. Never forcibly open the door before the washer
reaches the safe state to avoid damage to the door or scald. “Click” will be heard when opening the
door. It is normal and arises from the working principle of electromagnetic lock’s internal structure.
10. Cut off the water supply and power supply after finishing washing every time. Moreover, clean the
sight glass window pad interlining to prevent contaminants from tainting the clothes again or the
surface of window pad from going moldy.
11. When the washer is not in use, please keep the door slightly open to avoid unpleasant smell. Do
not cover the washer with a plastic bag to avoid moisture staying in the washer.
12. If the washer is feed water from a water tank and the difference
between the lowest height of water level in the water tank and the highest height of washer (table top)
is 0.1~0.5m, put a proper amount of detergent along with the clothes into the washer’s inner drum or
dilute the detergent and add it in the washer through corresponding detergent before washing to
prevent it from staying in the washer and affecting the washing and rinsing effect. It is not
recommended to select the prewash function and add softener in the washer in the above-mentioned
situations.
13. Washing capacity
before Washing
Check the clothes for special washing
requirements and make sure that the clothes are
suitable for washing with a washing machine and
water in order to avoid the deformation and
damage of the clothes.
For the clothes tainted with much mud
and dust, please remove them before
washing.
Wash those clothes liable to color fading
separately from other clothes.
Check pockets and remove coins,
sand, hairpin and other things
from them.
To avoid the sound from buttons,
please turn those clothes with
buttons inside out before putting
them into the washer.
Please unfold and fluff out the clothes before
putting them into the washer. Furthermore, do
not overload the washer.
When washing small articles (e.g. handkerchief,
gloves and socks, etc.) and those clothes liable
to intertwist and wear, please put them into net
bags for washing, rinsing and spinning to prevent
them from falling between the inner drum and
window pad and further avoid incomplete
washing or damage to top-grade clothes. The
weight of articles in each net bag should not
exceed 300g and the net bags should not be
washed together with those clothes not in a net
bag, otherwise the washer will not be balanced,
resulting in abnormal vibration.
Tie the ties, buckle the buttons, zip the zippers
and sew the openings.
5. Operational Procedure
Connect the water
inlet pipe and turn
on the water tap
Insert the power
plug into a power
socket.
Put down the
drain pipe.
Turn on the
power
switch.
Select the desired
program.
The “Delay” program is off by default.
To activate this program, press the
“Delay” button to make settings.
Start the selected
program.
Select the washing temperature, spinning speed,
“Delay” function, times of extra rinse and
“Intense” function, etc. as required.
Open the door, put the clothes into the washer and
close the door. Then add a proper amount of detergent
into corresponding distributor box and close it (refer to
the section of “Distributor Boxes” under “Notice before
Use” for details).
After finishing washing, the washer will automatically switch off.
Automatic Drum Washer
Operating Instructions
HW60-B12866NZP
220-240V/50H z
Power supply
Water inlet pressure
Rated washing capacity
Rated spinning capacity
Spinning speed
Washing noise
Spinning noise
Fadeless
cotton fabric
Wool fabric
Terylen fabric/blend
fabric/chemical fiber fabric
6 kg
3kg
1kg
1200r/m
50dB (A weighted)
68dB (A weighted)
6.0kg
6.0kg
time
time
Cotton
Prewash
Synthetic
Wool
Quick
Sport Wash
Hand Wash
Heavy
Underwear
Rinse
Spin
Drain
S-D Inverter
Speed
Temp.
Delay Strong
Start
Pause
Power
Extra Rinse Anti-crease
Speed Up
Press and hold 2 seconds
to set door unlocked
Night Wash
HW60-B12866NZP
6.0kg
445mm
510mm
940mm
Felt
1. Remove the adhesive from the back side of the felt and paste
the felt onto the back side of the protection board in a
symmetrical position to the board’s corners;
2. Incline the washer backwards and remove fourfeet(Fig.1);
3. Place the side with dimpled grain of rat guard inwards, then
pass foot bolts through four holesand tighten them to fix the rat
guard to the shell(Fig. 2) and finally level the washer.