Philips CMP200 User Manual

Download Operation & user’s manual of Philips CMP200 Amplifier, Car Amplifier for Free or View it Online on All-Guides.com.

Brand: Philips

Category: Amplifier , Car Amplifier

Type: Operation & user’s manual for Philips CMP200

Pages: 2 (1.3 Mb)

Download Philips CMP200 Operation & user’s manual

Philips CMP200 Operation & user’s manual - Page 1
1
Philips CMP200 Operation & user’s manual - Page 2
2
Register your product and get support at
www.philips.com/welcome
CMP200
EN User manual
RU Руководствопользователя
A
G
C
E
F
D
B
a
a
b
c
b
c
English
1. Important
Safety
Read and understand all instructions before you use the apparatus. If damage
is caused by failure to follow instructions, the warranty does not apply.
This unit is designed for negative ground (earth) 12 V DC operation only.
Use only the supplied mounting hardware for a safe and secure installation.
Do not connect any active speakers (with built-in amplier) to the speaker
terminals of the unit. Doing so may damage the active speakers.
To ensure safe driving, adjust the volume to a safe and comfor table level.
To avoid short circuit, do not expose the apparatus to rain or water.
Never expose the apparatus to direct sunlight, naked ames or heat.
Clean the apparatus with soft, damp cloth. Never use substances such as
alcohol, chemicals or household cleaners on the apparatus.
Notice
Environmental information
All unnecessary packaging has been omitted. We have tried to make the
packaging easy to separate into three materials: cardboard (box), polystyrene
foam (buffer) and polyethylene (bags, protective foam sheet.)
Your system consists of materials which can be recycled and reused if
disassembled by a specialized company. Please obser ve the local regulations
regarding the disposal of packaging materials, exhausted batteries and old
equipment.
Any changes or modications made to this device that are not expressly
approved by Philips Consumer Lifestyle may void the user’s authority to
operate the equipment.
2009 © Koninklijke Philips Electronics N .V. All rig hts reser ved.
Specications are subject to change without notice. Trademarks are the property of Koninklijke Philips
Elec tronics N.V. or their respective owners. Philips reserves the ri ght to change pr oduc ts at a ny time
with out be ing obliged to a djus t earlier supplies accor dingly.
2. Your car power amplier
Congratulations on your purchase, and welcome to Philips!
To fully
benet from the support that Philips offers, register your product at
www.philips.com/welcome.
Introduction
With the amplier, you can enjoy high quality sound performance with
powerful bass and beats.
What’s in the box
A
Check and identify the contents of your package:
a Amplier
b Screw_4x25mm (x4)
c Fuse (x2)
d Hi input connector (x1)
Overview of the main unit
B
a OUTPUT L/R
Connect additional amplier for additional speakers.
b
INPUT L/R
Connect car audio with RCA cable.
c HI INPUT
Connect car audio with the supplied high input connector.
d
INPUT LEVEL
Adjust input level (0.3V to 6V).
e
PROTECT
Light in red when the PROTECTOR is activated.
f
POWER
Light in blue when power is turned on.
g
FREQ
Adjust frequency of HPF or LPF from 30Hz to 400Hz.
h HPF/OFF/LPF
Select High-pass-lter (HPF), Low-pass-lter(LPF) or OFF (at)
mode.
i BASS BOOST
Boost the frequencies at around 45Hz to a maximum of 12dB.
j
POWER (GND/REM/+12V)
Connect +12V DC power cable, ground wire and remote wire.
k
Fuse: 30Ax2
l SPEAKER OUTPUT
Connect to speakers or subwoofers.
3. Installation
Installation
C
You can mount the amplier either under a seat or on the rear tray.
Note
To avoid interference, do not place the amplier too close to the car audio or
antenna.
The supplied mounting screws are 25mm long. Make sure that the mounting
board is thicker than 25mm.
1
Place the unit on the location for installation.
2
Mark the positions of the four screw holes.
3
Drill the holes with driller of approximately 4mm in diameter.
4
Mount the unit with the supplied screws.
Connect speakers
D
Note
Use speakers with an impedance of 2 to 8 ohm (4 to 8 ohm when used as a
bridged amplier).
Match the “lef t”, “right”, “+” and “-” terminals correctly. Revised polarity may
degrade sound quality.
Option 1: Mono bridged mode: connect 1 speaker
a
Option 2: Stereo mode: connect 2 speakers
b
Option 3: Tri-mode: connect 3 speakers
c
Connect car audio
E
Option 1: High level input connection
a
Connect the amplier to your car audio with the supplied High level
input connector.
Option 2: Line input connection
b
Connect the amplier to the car audio with a RCA cable (not supplied).
Option 3: Line output connection
c
Connect the amplier to another amplier.
Connect power
F
1
Make the power connection as illustrated below:
Connect the ground wire from the car to the GND socket.
Connect the remote wire from the car audio to the
REM socket.
With this connection, you can turn on/off the amplier
with the car audio.
Connect the power wire from the car battery to the
+12V
socket.
Tip
If your car audio does not have remote output, connect the remote input
terminal (REM) to the accessory power supply.
4. Use your power amplier
Select crossover frequency mode
You can select crossover frequency mode as below:
HPF (high-pass-lter) mode Select this mode when mid-range speaker s and
tweeters are connected for high frequency output.
LPF (Low-pass-lter) mode Select this mode when woofer and subwoofer is
connec ted for low frequency output.
OFF (at) mode Select this mode when tri-mode speaker connection
is used.
1
Slide HPF/OFF/LPF to the selected positon.
Adjust frequency
You can adjust frequency of HPF or LPF from 30HZ to 400Hz.
Note
When the
HPF/OFF/LPF switch is set at OFF position, the frequency adjustment
does not work.
1
Rotate FREQ to select frequency.
Adjust input level
You can adjust the input voltage from 0.3V to 6V.
1
Rotate INPUT LEVEL to adjust input voltage.
Adjust bass boost
You can punch extra bass for 0 to 12dB.
1
Rotate BASS BOOST to punch for extra bass.
About the protector indicator
The amplier has a built-in protection circuit to protect the transistors
and speakers when:
The unit is overheated. Or
A DC current is generated. Or
The battery voltage is over low or over high. Or
The speaker terminals are short circuited.
When the PROTECT indicator lights up in red, the unit shuts down
automatically. If this happens, please:
1
Take out the disc or tape and turn off the car audio.
2
Check the cause of the malfunction (see above).
3
If the amplier has overheated, wait until the unit cools down
before use.
Replace fuse
G
If there is no power, the fuse may be damaged and need to be replaced.
1
Pull out the damaged fuse.
2
Replace the fuse with the supplied fuses or to buy two fuses
that matches the voltage of the damaged fuse (30Ax2).
If the fuse gets damaged immediately after it has been replaced, there
may be an internal malfunction. In such case, consult your Philips dealer.
5. Product information
Note
Product information is subject to change without prior notice.
Power Output (RMS)
- 4 ohm
- 4 ohm (bridged)
- 2 ohm
125 Wx2
380Wx1
190Wx 2
Total harmonic distortion 0.01%
Signal to noise ratio 106dB
Channel separation 50dB
Frequency response 5-100kHz
Input sensitivity 300mV-6V
Input impedance 22k ohm
Fuse rating 30Ax2
Dimensions (DxWxH) 54.4x336.5x240.2mm
ba
dc
a
lk
j
bc
dfeghi
RL
RL
4 ohm speaker
Динамик 4 Ом
RL
4 ohm speaker 4 ohm speaker
Динамик 4 Ом Динамик 4 Ом
8 ohm speaker
Динамик 8 Ом
RL
4 ohm speaker
Динамик 4 Ом
4 ohm speaker
Динамик 4 Ом
Left speaker
Right speaker
Car audio unit
Левый громкоговоритель
Правый громкоговоритель
Автомобильное
аудиоустройство
White / Black
White
Grey
Grey / Black
Белый
Серый
Белый/черный
Серый/черный
LINE OUT
Car audio unit
Автомобильное
аудиоустройство
Линейный выход
RL
to a metal point of the car
Car audio unit
Remote output
Fuse (60 A)
+12 V car battery
less than 450 mm (18 in)
К металлическому контакту в автомобиле
Выход для пульта ДУ
Автомобильное
аудиоустройство
Менее 450 мм (18 дюймов)
Плавкий предохранитель (60 А)
Автомобильный аккумулятор +12 В
CMP200_51_UM_V2.0_EN+RU.indd 1 12/9/2009 3:21:56 PM