Wheelock PS-4CA Installation Instructions
Download Installation instructions of Wheelock cm6520 Motherboard, Smoke Alarm for Free or View it Online on All-Guides.com. This version of Wheelock cm6520 Manual compatible with such list of devices, as: MF280, A88X-PLUS, H61M-PRO, B85-A, d-Color MF220
Category: Motherboard , Smoke Alarm
Type: Installation instructions
Model: Wheelock cm6520 , Wheelock MF280 , Wheelock MF360 , Wheelock PS-4CA , Asus A55BM-K , Asus A88X-PLUS , Asus CS-B , Asus H61M-PRO , Asus H81M-D PLUS , Wheelock B85-A , Wheelock d-Color MF220 , Wheelock H61M-F
Pages: 2 (0.15 Mb)
1
2
P84681 A
Sheet
1 of 2
273 Branchport Avenue
Long Branch, N.J. 07740 Thank you for using our products.
(732) 222-6880
INSTALLATION INSTRUCTIONS
MODEL PS-4CA
4 CLASS “A” MODULE
Use this product according to this instruction manual. Please keep this instruction manual for future reference.
NOTE: All CAUTIONS and WARNINGS are identified by the symbol
'. All warnings are printed in bold capital letters.
WARNING: INDICATES A POTENTIALLY HAZARDOUS SITUATION THAT, IF NOT AVOIDED, COULD RESULT IN PROPERTY DAMAGE
AND SERIOUS PERSONAL INJURY OR DEATH TO YOU AND OR OTHERS.
WARNING: READ THESE INSTRUCTIONS CAREFULLY. FAILURE TO COMPLY WITH ANY OF THE FOLLOWING INSTRUCTIONS,
CAUTIONS AND WARNINGS COULD RESULT IN IMPROPER APPLICATION, INSTALLATION AND/OR OPERATION OF THESE PRODUCTS IN
AN EMERGENCY SITUATION, WHICH COULD RESULT IN PROPERTY DAMAGE AND SERIOUS INJURY OR DEATH TO YOU AND/OR
OTHERS.
WARNING: TWO DIFFERENT SOURCES OF POWER MAY BE CONNECTED TO THIS UNIT. DISCONNECT BOTH SOURCES OF POWER
BEFORE SERVICING. FAILURE TO DISCONNECT BOTH POWER SOURCES BEFORE SERVICING COULD RESULT IN PROPERTY DAMAGE,
SERIOUS INJURY, OR DEATH TO YOU AND/OR OTHERS.
APPLICATION INFORMATION:
The PS-4CA is designed to plug into the POWERPATH power booster providing the capability for four (4) CLASS “A” Notification
Appliance Circuits (NAC). Each of the four (4) NAC’s has the capability of handling up to 3Amps of current. The total for all of the
NAC’s is not to exceed the total current capacity of the POWERPATH power booster.
MATERIALS:
The following items should be included this box:
One set of installation instructions (this is the installation instructions)
One - PS-4CA PC board
Two - female to male, 6-32 x 9/16” long, Teflon standoffs
Two - Screws 6-32, 1/4” long
INSTALLATION INSTRUCTIONS:
STEP 1: On the POWERPATH power booster, verify that AC power is OFF and Battery power is disconnected.
STEP 2: On the POWERPATH power booster PC board, the CLASS A/B wiring switch (SW9), should be set to the
“OFF” or CLASS “B” position.
STEP 3: Install the two (2) 6-32 x 9/16” Teflon standoffs, screwing the male end through the POWERPATH power
booster in the lower right portion of the PC board.
STEP 4: Align the four (4) connectors on the PS-4CA PC board with the four (4) connectors on the POWERPATH
power booster PC board.
STEP 5: Firmly press the PS-4CA PC board connectors into the proper connections on the POWERPATH power
booster until the bottom of the PS-4CA rests on the two (2) Teflon standoffs.
STEP 6: Screw the two (2) mounting screws through the mounting holes in the PS-4CA PC board. See figure 1
STEP 7: Refer to the POWERPATH power booster installation instructions to complete wiring and final check out.
Copyright 2005 Wheelock Inc. All rights reserved.