Philips CED750/51 User Manual
Download Quick start manual of Philips CED750/51 Car Receiver, Car Stereo System for Free or View it Online on All-Guides.com.
Brand: Philips
Category: Car Receiver , Car Stereo System
Type: Quick start manual for Philips CED750/51
Pages: 2 (1.57 Mb)
1
2
Register your product and get support at
CED750
ENG Quick Start Guide
RU ǗǽǭǿǷǻDzǽȀǷǻǯǻDZǾǿǯǻ
5 Touch the hour digits, then touch or .
6 Touch the minute digits, then touch or .
7 If 12 hour mode is selected, touch or
to select AM or PM.
8 Touch to exit.
Tune to a radio station
1
Touch to display the main menu.
2 Touch [Radio].
Band and frequency information is
»
displayed.
3 Touch [Band] repeatedly to select:
FM band options: FM1, FM2, FM3
AM band options: AM1, AM2
4 %ULHÁ\WRXFK[Previous] or [Next] to tune
to a radio station by step.
Play with RDS
The RDS (Radio Data System) function operates
only in areas with FM stations broadcasting RDS
signals. If you tune to an RDS station, an RDS icon
and information about the presenter, station or
program is displayed.
Select program type
Before tuning to RDS stations, you can select
program type and let the unit search only for
programs of the selected category.
1 Touch on FM band to select [FM1] or [FM2].
2 Touch [RDS].
3 Touch [PTY] .
4 Touch or to display the next/previous
screen.
5 Touch on the selected program to activate
searching.
Play discs
1 Insert the disc into the disc slot with label
side facing up.
Play starts automatically.
»
To remove the disc, press the
»
button.
When the disc is ejected, the unit switches
»
to the previous source, if connected. Other-
wise, the unit switches to [Radio] mode auto-
matically.
Insert USB or SD/MMC card
1 Open the USB/SD/MMC card cover.
2 Insert the USB device or SD/MMC card into
the USB socket or SD/MMC card slot.
Play starts automatically.
»
Pair the Bluetooth-enabled
devices
1
Turn on the Bluetooth function on the
device.
2 Setup the Bluetooth function on your device.
3 Select “CED750” in the pairing list.
4 Enter default password “0000”.
iI pairing succeeds.
»
[Connect] is displayed
on the panel.
Make a call
1
Pair the phone with the system.
2 Touch to return to main menu.
3 Touch [Bluetooth].
4 Touch to dial.
Receive call
1
If there is incoming call, [Incoming call…]
ÁDVKHVRQWKHVFUHHQ6SHDNLQWRWKH%OX-
etooth microphone.
2 When conversation ends, touch to
terminate the call.
1
1
2
3
4
5
6
7
8
9
0
!
English
Connect wires: ISO connectors
1
Pull out the ISO connectors from the car
dashboard and connect them to the bigger
end of the supplied standard connector.
2
Connect the other end of supplied standard
connector to the unit.
If necessary, connect the following:
Connector Connect to/with
1
Black cable Antenna
2
Yellow cable Video out 1
3
Yellow cable Video out 2
4
Yellow cable Camera in
5
Green/white
wire
Parking
6
Black cable Bluetooth microphone
7
Blue cable Subwoofer
8
Red cable Front line out L
9
White cable Front line out R
0
Red cable Rear line out L
!
White cable Rear line out R
Mount in the dashboard
1
If the car does not have an on-board drive or
navigation computer, disconnect the negative
terminal of the car battery.
If you disconnect the car battery in
a car that has an on-board drive or
navigation computer, the computer may
lost its memory.
If the car battery is not disconnected,
to avoid short-circuit, ensure that bare
wires do not touch each other.
2
Ensure that car dashboard opening is within
these measurements:
Since the unit cannot be used if the
dashboard opening’s slant angle is above
20 degrees: Ensure that the horizontal
slant of the car dashboard opening is
between 0 and 20 degrees
3
Remove the screws on the both side of the
unit.
4
Remove the mounting sleeve.
5
Install the sleeve into the dashboard and
EHQGWKHWDEVRXWZDUGWRÀ[WKHVOHHYH
6
Place the rubber cushion over the end of the
bolt.
7
Slide the unit into the dashboard until a click
sound is heard.
,IWKHXQLWFDQQRWÀWLQWRWKHGDVKERDUG
remove the mounting bracket on the
both side of the unit and replace them
with the supplied short mounting
brackets.
8
Attach the trim plate.
9
Reconnect the negative terminal of the car
battery.
Turn on
1
Press the to turn on the unit.
The screen opens automatically.
»
The available OSD (On-Screen Display)
»
languages are displayed.
2 Touch a language to select.
The OSD language is changed to the
»
selected language immediately.
To adjust the screen tilt, press
TILT .
To close the screen, press OPEN/CLOSE.
To adjust the brightness/contrast, press
/ ,
then adjust 4 WAY NAVIGATION.
To turn off the system, press
for 3 sec-
onds.
The screen closes automatically.
»
Set clock
1
Touch to display main menu.
2 Touch [Setting].
The setup menu is displayed.
»
3 Touch [General].
4 Touch the [Clock mode] repeatedly to
select:
[12hr] : 12 hour mode
[ 24hr] : 24 hour mode
2
183 mm
53.5mm
5mm
3
P
r
i
n
t
i
n
g
i
n
C
h
i
n
a
P
r
i
n
t
i
n
g
i
n
C
h
i
n
a
4
© 2009 Koninklijke Philips Electronics N.V.
All rights reserved.
CED750_51_QSG_V2.0