Stagg 10 AA USA User Manual
Download Operation & user’s manual of Stagg 10 AA USA Amplifier for Free or View it Online on All-Guides.com.
Brand: Stagg
Category: Amplifier
Type: Operation & user’s manual for Stagg 10 AA USA
Pages: 2 (0.38 Mb)
FRONT PANEL :
1. INPUT : This is a 1/4” (Ø 6.3 mm) input jack socket for plugging in an electro-acoustic instrument. We
recommend that you always use a high-quality shielded guitar cable to prevent any background noise
interference or unwanted feedback.
2. VOLUME : This control determines the output volume of any instrument plugged into the amplier via
the guitar input jack.
3. PASSIVE/ACTIVE SWITCH : This switch enables the user to choose between passive and active modes
according to whether the instrument connected is passive (without preamp) or active (with preamp).
4. TREBLE : This control determines the level of high frequencies in the output signal. Adding TREBLE will
make your guitar sound brighter and sharper.
5. MID : This control determines the level of middle frequencies in the output signal. Adding MID will make
your guitar sound rounder and fuller.
6. BASS : This control determines the level of low frequencies in the output signal. Adding BASS will make
your guitar sound warmer and heavier.
7. CD/MP3 INPUT : This is a line level 1/4” (Ø 6.3 mm) stereo jack into which an MP3/CD/Tape player
may be connected.
8. PHONES : This is a 1/4” (Ø 6.3 mm) stereo jack output to connect the headphones. When headphones
are connected, no sound is produced from the speaker.
9. POWER LED : When this red LED is lit, the amplier is ready to work. When it is off, it means the
amplier is powered off.
10. POWER : This switch turns the amplier on or off.
BACK PANEL:
WARNING: This amplier must be earthed. Please check that the supply voltage details given on the
rating label (located on the rear panel) are in accordance with your electricity supply.
1. POWER FUSE: In the event of the power fuse having to be replaced, rst unplug the power cable from
the mains outlet. Then remove the fuse cover and replace the power fuse with another fuse of the same
type and value. Never plug the power cable back into the mains outlet without the fuse cover. If the power
fuse blows up again when powering on the amplier, take the apparatus to a suitable service centre for
repair.
MAINS CABLE: This amplier features a power cable with a moulded-on plug. If the socket outlets in the
home are not suitable for the plug supplied with this amplier, use an appropriate plug adapter that can
handle the power required for this amplier. In case the power cable or plug is damaged, unplug it in a
safe way from the mains outlet and go to a suitable service centre for replacement.
TECHNICAL SPECIFICATIONS
Max. Rated Power / Loudspeaker
10 Watts RMS @ 8 Ohms load/ 6.5” Speaker w/
Coaxial Tweeter
Frequency Response 70 Hz to 12 kHz
Total Harmonic Distortion 0.2%
Signal to Noise Ratio - 68 dB @ max Rated Power
Input Impedance
180k Ohms
Power Consumption
20 Watts max
Maximum Input Level
30 mV (RMS)
Maximum Gain
48 dB (@ 1kHz)
Dimensions (H x W x D)
25.5 x 28 x 17.2 cm / 10 x 11 x 6.8 inch
Weight
4.5 kg / 9.9 lb
Features and Specications are subject to change without notice.
2 3
USER’S MANUALUSER’S MANUAL
active
passive
DATE:
INPUT: ~110V/60Hz
PWR: 16W
FUSE: T1AH/250V
1
1 2 3 4 5 6 7 8 9 10
10 AA USA 10 AA USA