Stagg 10 GA User Manual

Download Operation & user’s manual of Stagg 10 GA Amplifier, Musical Instrument Amplifier for Free or View it Online on All-Guides.com.

Brand: Stagg

Category: Amplifier , Musical Instrument Amplifier

Type: Operation & user’s manual for Stagg 10 GA

Pages: 2 (0.65 Mb)

Download Stagg 10 GA Operation & user’s manual

Stagg 10 GA Operation & user’s manual - Page 1
1
Stagg 10 GA Operation & user’s manual - Page 2
2
FRONT PANEL:
1. INPUT: Plug your guitar in here. We recommend that you always use a high-quality shielded guitar
cable to prevent any background noise interference or unwanted feedback.
2. GAIN: This control determines the distortion intensity of the amplier’s overdrive setting. Adding GAIN
will make your guitar sound more distorted.
3. OVERDRIVE: This switch activates the amplier’s built-in overdrive function, which adds distortion to
the signal.
4. VOLUME: This control determines the output volume of the amplier.
5. TREBLE: This control determines the level of high frequencies in the output signal. Adding TREBLE will
make your guitar sound brighter and sharper.
6. MID: This PARAMETRIC control determines the level of middle frequencies in the output signal. Adding
MID will make your guitar sound rounder and fuller.
7. BASS: This control determines the level of low frequencies in the output signal. Adding BASS will make
your guitar sound warmer and heavier.
8. HEADPHONES: This is a 1/8” (Ø 3.5 mm) mini-jack ( 10 GA model) or a 1/4” (Ø 6.3 mm) standard
jack ( 10 GA P model) output to connect the headphones. When headphones are connected, no sound is
produced from the speaker.
9. CD/MP3 INPUT: For 10 GA model only, this is a line level 1/8” (Ø 3,5 mm) stereo mini jack into which
an MP3/CD/Tape player may be connected.
10. POWER LED: When this red LED is lit, the amplier is ready to work. When it is off, it means the
amplier is powered off.
11. POWER: This switch turns the amplier on or off.
BACK PANEL:
WARNING: This amplier must be earthed. Please check that the supply voltage details given on the
rating label (located on the rear panel) are in accordance with your electricity supply.
1 MAINS CABLE: This amplier features a power cable with a moulded-on plug. If the socket outlets
in the home are not suitable for the plug supplied with this amplier, use an appropriate plug adapter that
can handle the power required for this amplier.
In case the power cable or plug is damaged, unplug it in a safe way from the mains outlet and go to a
suitable service centre for replacement.
2 POWER FUSE: In case the power fuse has to be replaced, rst unplug the power cable from the mains
outlet. Then remove the fuse cover and replace the power fuse with one of the same type and value. Never
plug the power cable back into the mains outlet without the fuse cover. When powering on the amplier,
if the power fuse blows up again, go to a suitable service centre for repair.
TECHNICAL SPECIFICATIONS
Max. Rated Power / Loudspeaker 10 Watts RMS @ 8 Ohms load / 6.5” Speaker
Frequency Response 70 Hz to 10 kHz
Total Harmonic Distortion 0.8% (Clean Mode)
Signal to Noise Ratio - 60 dB @ max Rated Power
Input Impedance
470k Ohms
Power Consumption
20 Watts max
Maximum Input Level
40 mV (RMS)
Maximum Gain
44 dB (@ 1kHz)
Dimensions (H x W x D) 29 x 28 x 18 cm / 11.4 x 11 x 7.1 in
Weight
4.3 kg / 9.5 lb
Features and Specications are subject to change without notice.
2 3
USER’S MANUALUSER’S MANUAL 10 GA & 10 GA P 10 GA & 10 GA P
1 2
1 2 3 4 5 6 7 8 11109