• Home
• Brands
• Stagg Manuals
• Stagg 40 BA USA
• Stagg 40 BA USA User Manual

Stagg 40 BA USA User Manual

Download Operation & user’s manual of Stagg 40 BA USA Amplifier for Free or View it Online on All-Guides.com.

1

2

BACK PANEL:

WARNING: This amplier must be earthed. Please check that the supply voltage details given on the

rating label (located on the rear panel) are in accordance with your electricity supply.

1 MAINS INPUT: This is the input socket into which the mains power cable must be connected. This

amplier is supplied with a power cable with a moulded-on plug. If the socket outlets in the home are

not suitable for this plug, use an appropriate plug adapter that can handle the power required for the

amplier.

2 POWER FUSE: In the event of the power fuse having to be replaced, rst unplug the power cable

from the mains outlet. Then remove the fuse cover and replace the power fuse with another fuse of the

same type and value. Never plug the power cable back into the mains outlet without the fuse cover. If

the power fuse blows up again when powering on the amplier, take the apparatus to a suitable service

centre for repair.

Features and Specications are subject to change without notice.

FRONT PANEL:

1. INPUT: Plug your bass in here. We recommend that you always use a high-quality shielded cable to

prevent any background noise interference or unwanted feedback.

2. VOLUME: This control determines the output volume of the amplier.

3. TREBLE: This control determines the level of high frequencies in the output signal. Adding TREBLE will

make your bass sound brighter and sharper.

4. MID: This control determines the level of middle frequencies in the output signal. Adding MID will make

your bass sound rounder and fuller.

5. BASS: This control determines the level of low frequencies in the output signal. Adding BASS will make

your bass sound warmer and heavier.

6. COMPRESSION: This control reduces the dynamic range of the output signal and evens out the

changes in volume that occur according to how hard you play your instrument. Adding COMPRESSION will

make your bass sound smoother and clearer.

7. CD/MP3 INPUT: This is a line level 1/4” (Ø 6.3 mm) stereo jack into which an MP3/CD/Tape player

may be connected.

8. PHONES: This is a 1/4” (Ø 6.3 mm) standard jack output to connect the headphones. When headphones

are connected, no sound is produced from the speaker.

9. POWER: This switch turns the amplier on or off. The switch is illuminated when the device is powered

on.

2 3

USER’S MANUALSUSER’S MANUAL 40 BA USA 40 BA USA

1 2

3

4 5 6 7 8 9

TECHNICAL SPECIFICATIONS

Max. Rated Power / Loudspeaker 40 Watts RMS @ 4 Ohms load/ 10” Speaker

Frequency Response 80 Hz to 15 kHz

Total Harmonic Distortion 0.8%

Signal to Noise Ratio - 60 dB @ max Rated Power

Input Impedance

220k Ohms

Power Consumption

70 Watts max

Maximum Input Level

65 mV (RMS)

Maximum Gain

47 dB (@ 1kHz)

Dimensions (H x W x D)

37 x 40 x 22.5 cm / 14.6 x 15.7 x 8.9 in.

Weight

10.3 kg / 22.7 lbs

CM

C US

L

I

S

D

T

E

E

R

T

E

T

K

N

I

CONF ORMS TO

UL STD . 60065

CERT IFIED T O

CAN/ CSA STD .

C22. 2 No.60 065:0 3

PWR: 40W

FUSE: T1AH/250V

AC INPUT

~110V/60HZ

DATE:

1

2