Stagg 40 GA DSP User Manual
Download Operation & user’s manual of Stagg 40 GA DSP Amplifier for Free or View it Online on All-Guides.com.
Brand: Stagg
Category: Amplifier
Type: Operation & user’s manual for Stagg 40 GA DSP
Pages: 2 (0.86 Mb)
1
2
FRONT PANEL:
1. INPUT: Plug your guitar in here. We recommend that you always use a high-quality shielded guitar
cable to prevent any background noise interference or unwanted feedback.
2. VOLUME: This control determines the output volume of the amplier’s clean setting.
3. (Overdrive) GAIN: This control determines the distortion intensity of the amplier’s overdrive setting.
Adding GAIN will make your guitar sound more distorted.
4. (Overdrive) SWITCH: This switch activates the amplier’s built-in overdrive function, which adds
distortion to the signal.
5. (Overdrive) VOLUME: This control determines the output volume of the amplier’s overdrive setting.
Adding VOLUME will make your distorted guitar sound louder and clearer.
6. TREBLE: This control determines the level of high frequencies in the output signal. Adding TREBLE will
make your guitar sound brighter and sharper.
7. MID: This control determines the level of middle frequencies in the output signal. Adding MID will make
your guitar sound rounder and fuller.
8. PARAMETRIC MID: This control allows you to ne tune your guitar sound by cutting or boosting the
mid frequency parameters of the output signal. At a low level, the PARAMETRIC MID control will emphasize
the lower mids, while increasing the level will bring out the upper mids. The PARAMETRIC MID control can
help you explore a wide variety of different guitar tones.
9. BASS: This control determines the level of low frequencies in the output signal. Adding BASS will make
your guitar sound warmer and heavier.
10. BUILT-IN EFFECT:
•SPRING REVERB (40 GA R only): This is the reverb intensity control. This controls the amount of
reverb that is added back to the original dry signal. Adding REVERB will produce a reverberation effect
in your guitar sound, as though you were playing in a large hall. A little can go a long way in adding that
special depth to your sound. If engaged, the reverb is always active in either overdrive or clean mode.
•DSP (40 GA DSP only):
- Volume: This control determines the mix level of the amplier’s internal DSP effects in relation to the
dry signal when DSP is engaged.
- Program: This selector enables the user to choose among 16 internal DSP effects: 1-Long dry Delay •
2-Flanger + short Reverb • 3-Flanger + long Reverb • 4-Short Delay w/ multiple repeat + medium Reverb
• 5-Medium Delay w/ multiple repeat + long Reverb • 6-Short Reverb 2 • 7-Medium Reverb 2 • 8-Deep
Chorus + medium Reverb • 9-Normal Chorus + short Reverb • 10-Short Delay w/ short repeat • 11-Slap-
back Delay • 12-Cathedral • 13-Large Hall • 14-Short Reverb 1 + very light Chorus • 15-Medium Reverb 1
• 16-Medium wet Delay w/ multiple repeat.
BACK PANEL:
WARNING: This amplier must be earthed. Please check that the supply voltage details given on the
rating label (located on the rear panel) are in accordance with your electricity supply.
1 MAINS INPUT: This is the input socket into which the mains power cable must be connected. This
amplier is supplied with a power cable with a moulded-on plug. If the socket outlets in the home are
not suitable for this plug, use an appropriate plug adapter that can handle the power required for the
amplier.
2 POWER FUSE: In the event of the power fuse having to be replaced, rst unplug the power cable
from the mains outlet. Then remove the fuse cover and replace the power fuse with another fuse of the
same type and value. Never plug the power cable back into the mains outlet without the fuse cover. If
the power fuse blows up again when powering on the amplier, take the apparatus to a suitable service
centre for repair.
TECHNICAL SPECIFICATIONS
Max. Rated Power / Loudspeaker 40 Watts RMS @ 4 Ohms load / 10” Speaker
Frequency Response 70 Hz to 15 kHz
Total Harmonic Distortion 0.2% (Clean Mode)
Signal to Noise Ratio - 72 dB @ max Rated Power
Input Impedance
180k Ohms
Power Consumption
80 Watts max
Maximum Input Level
85 mV (RMS)
Maximum Gain
43 dB (@ 1kHz)
Dimensions (H x W x D)
39 x 42 x 21 cm/ 15.4 x 16.5 x 8.3 in.
Weight
10.7 kg / 23.6 lbs
Features and Specications are subject to change without notice.
11. CD/MP3 INPUT: This is a line level 1/4” (Ø 6.3 mm) stereo jack into which an MP3/CD/Tape player
may be connected.
12. PHONES: This is a 1/4” (Ø 6.3 mm) stereo jack output to connect the headphones. When headphones
are connected, no sound is produced from the speaker.
13. POWER LED: When this red LED is lit, the amplier is ready to work. When it is off, it means the
amplier is powered off.
14. POWER: This switch turns the amplier on or off.
2 3
USER’S MANUALUSER’S MANUAL 40 GA R - 40 GA DSP 40 GA R - 40 GA DSP
1 2
40 GA DSP
40
8
7
8
9
10
11
12
13
14
15
16
1
2
3
4
5
6
1 2 3 4 5 6 7 8 119
12
13
14
10
10