• Home
• Brands
• Stagg Manuals
• Stagg 250 GAR212
• Stagg 250 GARH User Manual

Stagg 250 GARH User Manual

Download Operation & user’s manual of Stagg 250 GAR212 Musical Instrument Amplifier for Free or View it Online on All-Guides.com.

1

2

FRONT PANEL

1) INPUT - Plug your guitar in here. We recommend that you always use a high-quality shielded guitar

cable to prevent any background noise interference or unwanted feedback.

2) (CLEAN) VOLUME - This control determines the output volume of the amplier’s clean channel.

3) CHANNEL SELECT - This button can be used to switch between the Clean and Overdrive channels.

Alternatively, you may also select the channel via a footswitch (see FOOTSWITCH).

4) (OVERDRIVE) LED - This red LED lights up when the Overdrive channel is activated.

5) (OVERDRIVE) GAIN - This control determines the distortion intensity of the amplier’s overdrive

setting. Adding GAIN will make your guitar sound more distorted.

6) (OVERDRIVE) MASTER - This control determines the output volume of the amplier’s Overdrive

channel. Adding MASTER will make your guitar sound louder and more percussive.

7) BASS - This control determines the level of low frequencies in the output signal. Adding BASS will make

your guitar sound warmer and heavier.

8) MID - This control determines the level of middle frequencies in the output signal. Adding MID will

make your guitar sound rounder and fuller.

9) TREBLE - This control determines the level of high frequencies in the output signal. Adding TREBLE will

make your guitar sound brighter and sharper.

10) (SPRING) REVERB - This is the reverb intensity control. This controls the amount of reverb that

is added back to the original dry signal. Adding REVERB will produce a reverberation effect in your guitar

sound, as though you were playing in a large hall. A little can go a long way in adding that special depth to

your sound. If engaged, the reverb is always active in either overdrive or clean mode.

11) MASTER - This is the master volume control. It allows you to control the overall listening level of

both channels.

12) CD/MP3 INPUT - This is a line level 1/4" (Ø 6.3 mm) stereo jack into which an MP3/CD/Tape player

may be connected.

13) EFX SEND - This amplier is equipped with an effects loop which allows you to plug effects between

the preamp and the power amp. The EFX SEND jack is a line level 1/4” (Ø 6.3 mm) output jack into which

you may connect one or several outboard effects, eg Flanger, Delay, Chorus etc. The EFX SEND should be

connected to the input jack of the rst effect in your chain.

14) EFX RETURN - This is a line level 1/4" (Ø 6.3 mm) input jack into which you should connect the

output jack of the last effect in your chain. The effects loop may also be used with a multi-effects rack

system, or with a single effect.

15) FOOTSWITCH - This is a 1/4" (Ø 6.3 mm) input jack into which you may connect a footswitch

(included) which will enable you to switch between the Clean and Overdrive channels while playing.

16) BALANCED OUT - This front panel XLR socket drives a post E.Q, post effects, balanced output signal

for connecting directly to one of the Balanced Microphone inputs of a mixing console.

17) POWER LED - When this red LED is lit, the amplier is ready to work. When it is off, it means the

amplier is powered off.

Features and Specications are subject to change without notice.

2 3

USER MANUALUSER MANUAL 250 GARH - 250 GAR212 250 GARH - 250 GAR212

BACK PANEL

WARNING

This amplier must be earthed. Please check that the supply voltage details given on the rear panel are in

accordance with your electricity supply.

1 POWER SWITCH - This switch turns the amplier on or off.

2 POWER FUSE - In the event of the power fuse having to be replaced, rst unplug the power cable from

the mains outlet. Then remove the fuse cover and replace the power fuse with one of the same type and

value. Never plug the power cable back into the mains outlet without the fuse cover. When powering on

the amplier, if the power fuse blows up again, go to a suitable service centre for repair.

3 MAINS INPUT - This is the input socket into which the mains power cable must be connected. This

amplier is supplied with a power cable with a moulded-on plug. If the socket outlets in the home are

not suitable for the plug supplied with this amplier, use an appropriate plug adapter that can handle the

power required for this amplier.

4 VOLTAGE SELECT - This switch selects the chosen voltage level between 110-120VAC and 220-

240VAC as appropriate. This switch may be accessed by unscrewing the safety cover. Always make sure

that the selected voltage level is in accordance with your electricity supply.

5 SPEAKER OUT - The 250 GARH head features two external speaker sockets to connect one (or two)

external Speaker Cabinet(s) providing the total load impedance is not lower than 4 Ohms, while the 250

GAR212 combo allows you to plug one external Speaker Cabinet only with a minimum load impedance of 8

Ohms, i.e: Stagg 150 GC412 (right model) and Stagg 150 GC412A (angled model), 150W RMS/8Ω Speaker

Cabinets for guitar amplier.

1 2 5 6 7 8 9

10 11 12 13 14 15 16 17

3 4

STAGG 250 GARH & STAGG 250 GAR212 STAGG 250 GARH & STAGG 250 GAR212

1 2 4 5 5 53

250 GARH 250 GAR212

TECHNICAL SPECIFICATIONS 250 GARH EU+UK 250 GAR212EU+UK

Description

250W RMS Guitar Amp Head

w/ Spring Reverb

250W Guitar Combo w/ Spring Reverb

and 2x 12” speakers

Max. Rated Power 250 Watts RMS @ 4 Ohms 250 Watts RMS @ 4 Ohms

Speakers (N * Ø/ P/ Z) 2 x 12"/ 80W/ 16 Ohms

External Speaker Out 2 x SPK 1 x SPK

Minimum Load 4 Ohms 8 Ohms

Frequency Response 60 Hz to 20 kHz 60 Hz to 20 kHz

Total Harmonic Distortion 0.5% (Clean Mode) 0.5% (Clean Mode)

Signal to Noise Ratio - 75 dB @ max Rated Power - 75 dB @ max Rated Power

Input Impedance 220k Ohms 220k Ohms

Power Consumption 600 Watts max 600 Watts max

Maximum Input Level 45 mV RMS 45 mV RMS

Maximum Gain 42 dB @ 1 kHz 42 dB @ 1 kHz

Dimensions (H x L x P) 23 x 73 x 31 cm 63 x 73.5 x 31 cm w/o casters

Dimensions (H x W x D) 9 x 28.7 x 12.2 in 24.8 x 28.9 x 12.2 in w/o casters

Weight 22.2 kg/ 48.9 lb 44.3 kg/ 97.7 lb