Honeywell ADEMCO 6150RF Installation And Setup Manual
Download Installation and setup manual of Honeywell ADEMCO 6150RF Keypad, Security System for Free or View it Online on All-Guides.com.
Brand: Honeywell
Category: Keypad , Security System , Transceiver
Type: Installation and setup manual for Honeywell ADEMCO 6150RF
Pages: 8 (0.13 Mb)
Download Honeywell ADEMCO 6150RF Installation and setup manual
K4460-1V4 7/03 Rev. B
ADEMCO 6150RF
Keypad/Transceiver
INSTALLATION AND SETUP GUIDE
About the ADEMCO 6150RF
The ADEMCO 6150RF Keypad/Transceiver is a combination unit that contains:
• An ADEMCO 6150 Fixed Addressable
Keypad
• An ADEMCO 5881M RF Receiver
• An ADEMCO 5800TM Transmitter
Module
• A normally-open relay output.
The ADEMCO 6150RF Keypad/Transceiver may be used on any ADEMCO control panel that supports the
ADEMCO 6150 Keypad.
Features of the 6150RF
Wireless Features
• Supports up to 8 wireless keys locally (programmed directly into 6150RF) without occupying any zones
supported by the control panel.
• Supports button-type transmitters (ADEMCO 5804, ADEMCO 5804BD) for local operation.
• Supports a maximum of 16 transmitters programmed into any ADEMCO 5800 Series-supported control
panel.
• Provides low-battery indications for the local wireless keys.
• Supports wireless keys with Signal Sentry (high-security) (ADEMCO 5804E).
• Provides a nominal range of 200' for the RF transmitters (some transmitters have a shorter range).
• Supports RF jam detection when the receiver is enabled.
• Provides wireless key support for control panels that do not support RF themselves (such as ADEMCO
4110DL).
U
L
The following ADEMCO 5800 series transmitters are not intended for use in UL installations: 5802, 5802MN,
5802MN2, 5804, 5804BD, 5804BDV, 5804E, 5804WATCH, 5814, 5816TEMP, 5819, 5819SBRS,
5819SWHS, and 5850.
Programming Features
• Provides an Auto Enroll mode for programming of the wireless keys.
• Provides a method for deleting a serial number and re-enrolling a new one in its place.
• Provides default settings for the functions of the wireless keys.
Additional Features
• Can send status signals (Armed, Ready, etc.) to bi-directional units such as ADEMCO 5804BD, ADEMCO
5804BDV and ADEMCO 5827BD.
• Can operate the on-board relay in conjunction with the receiver (e.g., to trip a garage door opener).
Note: This particular feature is not intended for UL installations.
• Can activate relays programmed into the control panel.
• Provides an End User mode to enable/disable local wireless keys (e.g., if a user accidentally loses a wireless
key). See the ADEMCO 6150RF User Guide for this procedure.
Application Guidelines
Use the following guidelines when planning an installation:
• Local wireless keys are programmed directly into the 6150RF and may be used regardless of whether the
RF receiver is enabled or disabled.
• If using bi-directional devices, be sure to enable the transmitter module in the 6150RF.
• If transmitters are programmed into the control panel, be sure to enable the receiver. (Make sure you do not
exceed the number of receivers supported by the control panel.)
• If a local wireless key is programmed to arm/disarm or to trigger a relay on the control panel, a user code
must be entered into the 6150RF. This user code must also be programmed into the control panel.
• You must set the House ID only if you are using RF keypads and/or bi-directional devices; AND the House
ID Source is the 6150RF (Local).