Audio Design Associates Cinema Reference Mach II PTM-6150 Installation Manual
Download Installation manual of Audio Design Associates Cinema Reference Mach II PTM-6150 Amplifier for Free or View it Online on All-Guides.com.
Brand: Audio Design Associates
Category: Amplifier
Type: Installation manual
Model: Audio Design Associates Cinema Reference Mach II PTM-6150 , Audio Design Associates Cinema Reference Mach II PTM-8150 , Audio Design Associates CINEMA REFERENCE Mach II
Pages: 113 (6.77 Mb)
Download Audio Design Associates Cinema Reference Mach II PTM-6150 Installation manual
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
Page 9
RECORD INPUT
DSS RECORD15
RECORD TAKEN
DVD PLAYER 1
The Cinema Reference Mach II incorporates a record selector that
operates independently from the actual source component selected
for the home theater room. This record selector can be used in
several ways.
1 Use the Record Selector to send audio and video signals
from a particular component to a recording device (i.e. VCR)
2 Use the Record Selector to send a video signals to a second
monitor or TV set. Ideal for the sports fanatic, this option would
permit a second TV to display a broadcast from a DSS receiver, TV
tuner, or VCR TV tuner, while the primary viewing display would be
set to a particular channel from another component.
3 Use the Record Selector to determine the image inserted
into a TV’s PIP (Picture In Picture). This would provide the same
effect as described in option 2 (above) using the PIP function in
place of a second TV or monitor.
4 Use the Record Selector to send the audio and video signal
of a particular device to a whole-house multi-room audio video sys-
tem. This setup would cause the Record Selector to act as a sepa-
rate zone from the actual home theater.
Please note, that the Record audio output of the Cinema Refer-
ence Mach II is a pure analog output. There is no analog-to-
digital or digital-to-analog conversion taking place in this cir-
cuit. This preserves the audio quality for those who opt to use
the Record output to pass audio to a premium two-channel
audio system. If a component is connected to a digital input
on the Cinema Reference Mach II, a special setup will need to
be done in order for the unit to play through the record output.
This is discussed under Recording Connections.
Record Selector Functions
To determine what component the
Record Selector is currently set to,
press the Record Selector knob.
The display will read as follows
where the second line of the dis-
play indicates the component se-
lected.
To select another source compo-
nent, turn the Record Selector
knob until the new component
appears in the display.
Then press the Record Selector
knob to engage this device.
Record Selector
The Record Selector operates
independently from the main
output providing the ability to
record, view, or play (in
another room) a component
other than the one selected in
the home theater.
To determine which device is
currently selected, press the
Record Selector knob. To
change components:
1. Dial In New Device
Turn the Record Selector knob
until the second line of the
LCD display reads the
component you wish to
select.
2. Engage New Device
Once the second line of the
display indicates the next
component you wish to
access, press the Record
knob to engage this input.
Side View
Press Knob
To Activate
The New
Component
Selection
Chassis Side
Front Plate
T
u
r
n
T
o
S
e
l
e
c
t
A
n
o
t
h
e
r
Front View
R
e
c
o
r
d
C
o
m
p
o
n
e
n
t
R
E
C
O
R
D