HP 202A Operating And Service Manual

Download Operating and service manual of HP 202A Processor for Free or View it Online on All-Guides.com.

Brand: HP

Category: Processor

Type: Operating and service manual for HP 202A

Pages: 47

Download HP 202A Operating and service manual

HP 202A Operating and service manual - Page 1
1
HP 202A Operating and service manual - Page 2
2
HP 202A Operating and service manual - Page 3
3
HP 202A Operating and service manual - Page 4
4
HP 202A Operating and service manual - Page 5
5
HP 202A Operating and service manual - Page 6
6
HP 202A Operating and service manual - Page 7
7
HP 202A Operating and service manual - Page 8
8
HP 202A Operating and service manual - Page 9
9
HP 202A Operating and service manual - Page 10
10
HP 202A Operating and service manual - Page 11
11
HP 202A Operating and service manual - Page 12
12
HP 202A Operating and service manual - Page 13
13
HP 202A Operating and service manual - Page 14
14
HP 202A Operating and service manual - Page 15
15
HP 202A Operating and service manual - Page 16
16
HP 202A Operating and service manual - Page 17
17
HP 202A Operating and service manual - Page 18
18
HP 202A Operating and service manual - Page 19
19
HP 202A Operating and service manual - Page 20
20
HP 202A Operating and service manual - Page 21
21
HP 202A Operating and service manual - Page 22
22
HP 202A Operating and service manual - Page 23
23
HP 202A Operating and service manual - Page 24
24
HP 202A Operating and service manual - Page 25
25
HP 202A Operating and service manual - Page 26
26
HP 202A Operating and service manual - Page 27
27
HP 202A Operating and service manual - Page 28
28
HP 202A Operating and service manual - Page 29
29
HP 202A Operating and service manual - Page 30
30
HP 202A Operating and service manual - Page 31
31
HP 202A Operating and service manual - Page 32
32
HP 202A Operating and service manual - Page 33
33
HP 202A Operating and service manual - Page 34
34
HP 202A Operating and service manual - Page 35
35
HP 202A Operating and service manual - Page 36
36
HP 202A Operating and service manual - Page 37
37
HP 202A Operating and service manual - Page 38
38
HP 202A Operating and service manual - Page 39
39
HP 202A Operating and service manual - Page 40
40
HP 202A Operating and service manual - Page 41
41
HP 202A Operating and service manual - Page 42
42
HP 202A Operating and service manual - Page 43
43
HP 202A Operating and service manual - Page 44
44
HP 202A Operating and service manual - Page 45
45
HP 202A Operating and service manual - Page 46
46
HP 202A Operating and service manual - Page 47
47
Sect.
lV
Page 4
4-8
TUBE REPLACEMENT CHART
TABLE 4-6.
4-9
POWER SUPPLY REGULATOR
ADJUSTMENT
TUBE
Vl, V2
V3
V4
V5, V6
V7, V8
V15,
Vl6, V17
Vl8, Vl9, V20
V21
V22, V23, V24, V25
Resistance measured between inner and outer chassis
should be at least two
megohms with OUTPUT ter-
minals disconnected from panel ground or a load.
This resistance check should be
made
before starting
the following adjustment procedure:
1) Connect the shorting strap between the lower
output terminal and chassis ground. Connect the dc
voltmeter between
B-
and the inner chassis. The
voltmeter must not be grounded and the common
terminal should
be
connected to
B-.
EFFECT
None. Variations in bottoming
voltage eliminated by clamps
V7
and V8.
Frequency shift and distortion
increase due to contact potential
variations.
DC output level shift, probably
as a function of amplitude con-
trol setting.
Possible change in frequency,
distortion, or dc balance from
change in regulated voltages.
Same effect as change in V3
possible, but to much less
degree.
Frequency change and unbalance
of triangle.
Change in dc output component,
independent of AMPLITUDE
control setting.
No effect
Possible change in
+
375 and
+
225 regulated voltages.
2) Connect the 202A
to
the power line and turn on.
The voltmeter indication should be between
+
190
and
+
230 volts with line voltage set to 115 volts.
READJUSTMENT
None.
Min. Distortion and Correct
Freq. Adj.
DC Bal. Adj.
Power Supply.
DC
Bal Adjust.
Minimum Distortion and
Correct Freq. Adjust.
Min. Distortion and Correct
Freq. Adj.
Min. Distortion and Correct
Freq. Adj.
Set dc output component to
zero by R65, with amplitude
control min.
None.
/
Carry out procedure under
"Power Supply Regulator
Adjustment". Paragraph
4-9.
.
3) Measure the regulated output voltage between
B-
and pin 2 of
tube
V5. Adjust control R11 to give
a voltage of
+
225 volts.
4)
Measure the voltage between pin
5
of tube V5 and
B-.
This voltage should be about
+
375 volts. Var-
iations in OA3 tubes can cause this voltage
to
be
as
low
as
365 or as high
as
393.