• Lightweight microminiature headset with ergonomic under-ear
design
•
Terminated for use with all Audio-Technica UniPak™ wireless
systems and many other manufacturers' wireless systems
• Exceptional sound quality and rugged construction
• Adjustable fit for left or right ear
• Available in black, cocoa (-CO) and beige (-TH) models
With a capsule diameter of just 2.5 mm, Audio-Technica's MicroSet
provides the ultimate in low-profile, high-performance audio. This
omnidirectional condenser microminiature headworn mic offers an
ergonomic under-ear design: its flexible, lightweight contoured loop
hooks behind the ear for an ultra-secure, comfortable fit with or with-
out glasses.
Operation: MicroSet's flexible design
enables it to be worn on either the left
or right ear. Position the lightweight
contoured loop around the back of
your ear, so that the boom extends
from the bottom of your ear as shown.
Bend the loop as needed to achieve a
secure, comfortable fit, so that the
MicroSet is not dislodged by shaking
your head. Remove the MicroSet and
bend a gentle curve in the micro-
phone's boom. Hook the MicroSet
back around your ear, and adjust the
boom as needed to follow the contour
of your face, positioning the micro-
phone near the corner of your mouth.
MicroSet has a large acoustical sweet spot; experiment with
placement near the corner of your mouth for optimal performance.
A cab
le clip is provided for strain relief, allowing the MicroSet to
remain securely in place without the w
eight of the cab
le pulling on
the headset. To install the cable clip, slip the cable into the snap-on
connector and attach the clip to clothing, leaving enough slack on the
MicroSet side of the clip to allow for free, comfortable motion.
The don
ut-shaped moisture guard is provided to protect the
element from s
w
eat and moisture
.
P
osition the moisture guard as
close to the element as possible to provide maximum protection. To
remo
v
e the moisture guard, first remove the element cover and place
it out of harm's way. Gently slide the moisture guard over the ele-
ment. Replace the element cover.
Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224
Audio-Technica Limited, Old Lane, Leeds LS11 8AG England
www.audio-technica.com
P51794 ©2005 Audio-Technica U.S., Inc. Printed in U.S.A.
MicroSet
™
MICROSET SPECIFICATIONS
†
ELEMENT Condenser
POLAR PATTERN Omnidirectional
FREQ
UENCY RESPONSE
20-20,000 Hz
OPEN CIRCUIT SENSITIVITY –44 dB (6.3 mV) re 1V at 1 Pa*
MAXIMUM INPUT SOUND LEVEL 122 dB SPL, 1 kHz at 1% T.H.D.
SIGNAL-T
O-NOISE RATIO
1
60 dB
, 1 kHz at 1 Pa*
CURRENT CONSUMPTION 0.1 mA typical @ 5V
VOLTAGE RANGE 2.5-11V
WEIGHT 0.08 oz (2.4 g)
(microphone, boom & earpiece)
DIMENSIONS
MICROPHONE
0.32" (8.1 mm) long,
0.11" (2.7 mm) diameter
BOOM 3.87" (98.4 mm) long,
0.042" (1.07 mm) boom
diameter
CABLE LENGTH 55" (1.4 m)
CABLE TERMINATIONS
AT892c, AT892c-CO, AT892c-TH Unterminated**
AT892cL4, AT892cL4-CO, Terminated for Sennheiser
AT892cL4-TH wireless systems using Lemo
connector
AT892cLM3, AT892cLM3-CO, Terminated for Sennheiser
AT892cLM3-TH wireless systems using locking
3.5 mm connector
AT892cT4, AT892cT4-CO, Terminated for Shure wireless
AT892cT4-TH systems using TA4F connector
AT892cT5, AT892cT5-CO, Terminated for ATW-U101 and
AT892cT5-TH Lectrosonics wireless systems
using TA5F connector
AT892cW, AT892cW-CO, AT892cW-TH Terminated with locking 4-pin
connector for use with A-T
UniPak
™
body-pack transmitters
ACCESSORIES FURNISHED Two windscreens; two element
covers; clothing clip; moisture
guard; carrying case
†
Specifications derived by using AT8537 power module. In the interest of standards
development, A.T.U.S. offers full details on its test methods to other industry professionals
on request.
*1 Pascal = 10 dynes /cm
2
= 10 microbars = 94 dB SPL
1
Typical, A-weighted, using Audio Precision System One.
**For use with Sennheiser wireless units, place a 15kΩ
resistor between the mic audio
and ground/shield lines, and a 2.2 nF capacitor between the bias + in and ground/shield lines.
Terminate with the appropriate connector as shown in the diagrams below.
Specifications are subject to change without notice.
WIRELESS OMNIDIRECTIONAL CONDENSER
HEADWORN MICROPHONES