Hunter 99111 Getting Started

Download Getting started of Hunter 99111 Fan for Free or View it Online on All-Guides.com.

Brand: Hunter

Category: Fan

Type: Getting started for Hunter 99111

Pages: 2

Download Hunter 99111 Getting started

Hunter 99111 Getting started - Page 1
1
Hunter 99111 Getting started - Page 2
2
www.HunterFan.com
1.888.830.1326
Model #99111
Universal Ceiling Fan
Wall Control
Getting Started
Wiring the Receiver Wiring the Wall Control
OR OR OR
Remove the canopy. If uncertain how
to remove it, reference the fan’s owner’s
manual. With wiring exposed, it may be
helpful to note existing wire connections
or take a digital photo for reference.
Remove the wire connectors that connect
the wires from the outlet box to the fan,
leaving the grounding wires connected.
CONNECT WIRES FROM
RECEIVER TO FAN -Using
the blue wire connectors
connect the white wire
from the receiver (marked
common out”) to the white
wire from fan. Connect the
black wire from the receiver
(marked “fan out”) to the
black wire from the fan.
Connect the blue wire from
the receiver (marked ”light
out”) to the blue wire (or
possibly black with white
stripe) from the fan. Note:
The red wire from the
receiver has a pre-installed
wire terminator. It will not
be used.
If you are uncertain about
wire colors or connections,
please contact a qualied
electrician.
CONNECT WIRES FROM
RECEIVER TO WIRES FROM
OUTLET BOX - Using an
orange wire connector
connect the black wire
(ungrounded) from the
ceiling to the black wire from
the receiver (marked “live
in”). Connect the white wire
(grounded) from the ceiling
to the white wire from the
receiver (marked “neutral in”).
AFTER ALL WIRES ARE
CONNECTED and secured
with wire connectors,
re-install the canopy.
Before installing the Universal
Remote Control Receiver,
use the pull chains to set the
fan speed to HIGH and the
light to ON. Be sure power is
OFF before proceeding with
installation.
Choose the hanging system that most closely resembles the one used by your fan and install the receiver and wire as directed.
Note: Some fans may have considerable excess lead wire. For easier canopy installation, cut the excess wire, leaving a minimum of 8” remaining. Re-strip the fan lead wires 1/2”. Place remaining excess wire into
the ceiling electrical box. The bracket and fan must remain properly grounded.
You may have installation issues if the fan is installed on an angled ceiling.
Ceiling
Plate
Receive
r
Canopy
Receiver
Canopy
Ceiling
Bracket
Receiver
Fan Body
Cable Tie
For low prole fans, the receiver should
be secured to the hanger bracket with
a cable tie.
Receiver
Canopy
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by turning off
the circuit breakers to the outlet box and associated wall switch location. If you cannot lock the circuit breakers
in the off position, securely fasten a prominent warning device, such as a tag, to the service panel.
M0033-01 • 09/17/12 • © Hunter Fan Company
F
R
O
M
R
E
C
E
I
V
E
R
white
black
blue
white (common out)
black (fan out)
blue (light out)
F
R
O
M
F
A
N
F
R
O
M
R
E
C
E
I
V
E
R
F
R
O
M
C
E
I
L
I
N
G
black (ungrounded)
white (grounded) white (neutral in)
black (live in)
OFF
Turn Power
After removing the switch plate
cover, remove all wiring from
the switch.
Using orange wire connectors,
connect the two black wires
(ungrounded) from the outlet
box. Also connect the two green
or bare wires (grounding) from
the outlet box with the grounding
wire from the wall control.
Insert the wall control into
the outlet box and secure the
two screws using a Phillips
head screwdriver.
Install the cover plate using a
Phillips Head screwdriver to
secure the two cover plate screws.