Husqvarna 323R Operator's Manual

Download Operator's manual of Husqvarna 323R series Brush Cutter, Trimmer for Free or View it Online on All-Guides.com. This version of Husqvarna 323R series Manual compatible with such list of devices, as: 325R X-SERIES, 325RD, 325RD X-SERIES, 325RDX, 325RX

Husqvarna 323R series Operator's manual - Page 1
1
Husqvarna 323R series Operator's manual - Page 2
2
Husqvarna 323R series Operator's manual - Page 3
3
Husqvarna 323R series Operator's manual - Page 4
4
Husqvarna 323R series Operator's manual - Page 5
5
Husqvarna 323R series Operator's manual - Page 6
6
Husqvarna 323R series Operator's manual - Page 7
7
Husqvarna 323R series Operator's manual - Page 8
8
Husqvarna 323R series Operator's manual - Page 9
9
Husqvarna 323R series Operator's manual - Page 10
10
Husqvarna 323R series Operator's manual - Page 11
11
Husqvarna 323R series Operator's manual - Page 12
12
Husqvarna 323R series Operator's manual - Page 13
13
Husqvarna 323R series Operator's manual - Page 14
14
Husqvarna 323R series Operator's manual - Page 15
15
Husqvarna 323R series Operator's manual - Page 16
16
Husqvarna 323R series Operator's manual - Page 17
17
Husqvarna 323R series Operator's manual - Page 18
18
Husqvarna 323R series Operator's manual - Page 19
19
Husqvarna 323R series Operator's manual - Page 20
20
Husqvarna 323R series Operator's manual - Page 21
21
Husqvarna 323R series Operator's manual - Page 22
22
Husqvarna 323R series Operator's manual - Page 23
23
Husqvarna 323R series Operator's manual - Page 24
24
Husqvarna 323R series Operator's manual - Page 25
25
Husqvarna 323R series Operator's manual - Page 26
26
Husqvarna 323R series Operator's manual - Page 27
27
Husqvarna 323R series Operator's manual - Page 28
28
Husqvarna 323R series Operator's manual - Page 29
29
Husqvarna 323R series Operator's manual - Page 30
30
Husqvarna 323R series Operator's manual - Page 31
31
Husqvarna 323R series Operator's manual - Page 32
32
Husqvarna 323R series Operator's manual - Page 33
33
Husqvarna 323R series Operator's manual - Page 34
34
Husqvarna 323R series Operator's manual - Page 35
35
Husqvarna 323R series Operator's manual - Page 36
36
Husqvarna 323R series Operator's manual - Page 37
37
Husqvarna 323R series Operator's manual - Page 38
38
Husqvarna 323R series Operator's manual - Page 39
39
Husqvarna 323R series Operator's manual - Page 40
40
24 – English
MAINTENANCE
1151416-95 Rev. 1 2008-12-23
Carburetor
Your Husqvarna product has been designed and
manufactured to specifications that reduce harmful
emissions. After the engine has used 8-10 tanks of fuel the
engine will be run-in. To ensure that it continues to run at peak
performance and to minimise harmful exhaust emissions
after the running-in period, ask your dealer/service workshop
(who will have a rev counter at their disposal) to adjust your
carburettor.
Function
The carburetor governs the engine’s speed via the throttle
control. Air and fuel are mixed in the carburetor. The air/
fuel mixture is adjustable. Correct adjustment is essential
to get the best performance from the machine.
The setting of the carburetor means that the engine is
adapted to local conditions, for example, the climate,
altitude, fuel and the type of 2-stroke oil.
The carburetor has three adjustment controls:
L = Low speed jet
H = High speed jet
T = Idle adjustment screw
The L and H-jets are used to adjust the supply of fuel to
match the rate that air is admitted, which is controlled with
the throttle. If they are screwed clockwise the air/fuel ratio
becomes leaner (less fuel) and if they are turned anti-
clockwise the ratio becomes richer (more fuel). A lean
mixture gives a higher engine speed and a rich mixture
gives a lower engine speed.
The T-screw regulates the throttle setting at idle speed. If
the T-screw is turned clockwise this gives a higher idle
speed; turning it anti-clockwise gives a lower idle speed.
Basic setting
The basic carburetor settings are adjusted during testing
at the factory. The basic setting is richer than the optimal
setting and should be maintained for the first few hours the
machine is in use. The carburettor should then be finely
adjusted. Fine adjustment should be carried out by a
skilled technician.
CAUTION! If the cutting attachment rotates when the engine
is idling the idle adjustment screw T should be turned anti-
clockwise until the cutting attachment stops.
Rec. idle speed 2700 rpm
Recommended max. speed: See the Technical data section.
Fine adjustment
When the machine has been ”run-in” the carburetor
should be finely adjusted. The fine adjustment should
be carried out by a qualified person. First adjust the L-
jet, then the idling screw T and then the H-jet.
Conditions
Before any adjustments are made, make sure that the air
filter is clean and the air filter cover is fitted. If you adjust
the carburettor when the air filter is dirty it will result in a
leaner mixture when the filter is finally cleaned. This can
lead to serious engine damage.
Carefully turn both jets, L and H, so that they are midway
between fully screwed in and fully screwed out.
Do not attempt to adjust the L and H jets beyond either
stop as this could cause damage.
Now start the machine according to the starting
instructions and let it warm up for 10 minutes.
CAUTION! If the cutting attachment rotates when the
engine is idling the idle adjustment screw T should be
turned anti-clockwise until the cutting attachment stops.
Low speed jet L
Try to find the highest idling speed, turning the low speed
needle L clockwise respectively counter-clockwise. When the
highest speed has been found, turn the low speed needle L 1/
4 turn counter-clockwise.
CAUTION! If the cutting attachment rotates when the engine
is idling the idle adjustment screw T should be turned anti-
clockwise until the cutting attachment stops.
!
WARNING! The complete clutch cover and
shaft must be fitted before the machine is
started, otherwise the clutch can come loose
and cause personal injury.
!
WARNING! If the idle speed cannot be
adjusted so that the cutting attachment
stops, contact your dealer/service
workshop. Do not use the machine until it
has been correctly adjusted or repaired.
L
+ 1/4