Husqvarna 327LD X-series Operator's Manual

Download Operator's manual of Husqvarna 327LD X-series Brush Cutter, Trimmer for Free or View it Online on All-Guides.com.

Husqvarna 327LD X-series Operator's manual - Page 1
1
Husqvarna 327LD X-series Operator's manual - Page 2
2
Husqvarna 327LD X-series Operator's manual - Page 3
3
Husqvarna 327LD X-series Operator's manual - Page 4
4
Husqvarna 327LD X-series Operator's manual - Page 5
5
Husqvarna 327LD X-series Operator's manual - Page 6
6
Husqvarna 327LD X-series Operator's manual - Page 7
7
Husqvarna 327LD X-series Operator's manual - Page 8
8
Husqvarna 327LD X-series Operator's manual - Page 9
9
Husqvarna 327LD X-series Operator's manual - Page 10
10
Husqvarna 327LD X-series Operator's manual - Page 11
11
Husqvarna 327LD X-series Operator's manual - Page 12
12
Husqvarna 327LD X-series Operator's manual - Page 13
13
Husqvarna 327LD X-series Operator's manual - Page 14
14
Husqvarna 327LD X-series Operator's manual - Page 15
15
Husqvarna 327LD X-series Operator's manual - Page 16
16
Husqvarna 327LD X-series Operator's manual - Page 17
17
Husqvarna 327LD X-series Operator's manual - Page 18
18
Husqvarna 327LD X-series Operator's manual - Page 19
19
Husqvarna 327LD X-series Operator's manual - Page 20
20
Husqvarna 327LD X-series Operator's manual - Page 21
21
Husqvarna 327LD X-series Operator's manual - Page 22
22
Husqvarna 327LD X-series Operator's manual - Page 23
23
Husqvarna 327LD X-series Operator's manual - Page 24
24
Husqvarna 327LD X-series Operator's manual - Page 25
25
Husqvarna 327LD X-series Operator's manual - Page 26
26
Husqvarna 327LD X-series Operator's manual - Page 27
27
Husqvarna 327LD X-series Operator's manual - Page 28
28
Husqvarna 327LD X-series Operator's manual - Page 29
29
Husqvarna 327LD X-series Operator's manual - Page 30
30
Husqvarna 327LD X-series Operator's manual - Page 31
31
Husqvarna 327LD X-series Operator's manual - Page 32
32
Husqvarna 327LD X-series Operator's manual - Page 33
33
Husqvarna 327LD X-series Operator's manual - Page 34
34
Husqvarna 327LD X-series Operator's manual - Page 35
35
STARTING AND STOPPING
14English
Check before starting
Check that the support flange is not cracked due to
fatigue or due to being tightened too much. Discard
the support flange if it is cracked.
Ensure the locking nut has not lost its captive force.
The nut lock should have a locking force of at least 1.5
Nm. The tightening torque of the locking nut should be
35-50 Nm.
Check that the trimmer head and trimmer guard are
not damaged or cracked. Replace the trimmer head or
trimmer guard if they have been exposed to impact or
are cracked.
Never use the machine without a guard nor with a
defective guard.
All covers must be correctly fitted and undamaged
before you start the machine.
Starting and stopping
Starting
Primer bulb: Press the air purge repeatedly until fuel
begins to fill the bulb. The bulb need not be completely
filled.
Choke: Set the choke control in the choke position.
Hold the body of the machine on the ground using your
left hand (CAUTION! Not with your foot!). Grip the starter
handle, slowly pull out the cord with your right hand until
you feel some resistance (the starter pawls grip), now
quickly and powerfully pull the cord.
Never wrap the
starter cord around your hand
Repeat pulling the cord until the engine starts. When the
engine starts. return choke control to run position and
apply full throttle; the throttle will automatically disengage
from the start setting.
!
WARNING! The complete clutch cover
and shaft must be fitted before the
machine is started, otherwise the clutch
can come loose and cause personal
injury.
Always move the machine away from the
refuelling area before starting. Place the
machine on a flat surface. Ensure the
cutting attachment cannot come into
contact with any object.
Make sure no unauthorised persons are
in the working area, otherwise there is a
risk of serious personal injury. The safety
distance is 15 metres.
!
WARNING! When the engine is started
with the choke in either the choke or
start throttle positions the cutting
attachment will start to rotate
immediately.