Husqvarna 326Lx Operator's Manual

Download Operator's manual of Husqvarna 326Lx Chainsaw, Trimmer for Free or View it Online on All-Guides.com.

Brand: Husqvarna

Category: Chainsaw , Trimmer

Type: Operator's manual

Model: Husqvarna 326Lx , Husqvarna 326LX-series

Pages: 28

Download Husqvarna 326Lx Operator's manual

Husqvarna 326Lx Operator's manual - Page 1
1
Husqvarna 326Lx Operator's manual - Page 2
2
Husqvarna 326Lx Operator's manual - Page 3
3
Husqvarna 326Lx Operator's manual - Page 4
4
Husqvarna 326Lx Operator's manual - Page 5
5
Husqvarna 326Lx Operator's manual - Page 6
6
Husqvarna 326Lx Operator's manual - Page 7
7
Husqvarna 326Lx Operator's manual - Page 8
8
Husqvarna 326Lx Operator's manual - Page 9
9
Husqvarna 326Lx Operator's manual - Page 10
10
Husqvarna 326Lx Operator's manual - Page 11
11
Husqvarna 326Lx Operator's manual - Page 12
12
Husqvarna 326Lx Operator's manual - Page 13
13
Husqvarna 326Lx Operator's manual - Page 14
14
Husqvarna 326Lx Operator's manual - Page 15
15
Husqvarna 326Lx Operator's manual - Page 16
16
Husqvarna 326Lx Operator's manual - Page 17
17
Husqvarna 326Lx Operator's manual - Page 18
18
Husqvarna 326Lx Operator's manual - Page 19
19
Husqvarna 326Lx Operator's manual - Page 20
20
Husqvarna 326Lx Operator's manual - Page 21
21
Husqvarna 326Lx Operator's manual - Page 22
22
Husqvarna 326Lx Operator's manual - Page 23
23
Husqvarna 326Lx Operator's manual - Page 24
24
Husqvarna 326Lx Operator's manual - Page 25
25
Husqvarna 326Lx Operator's manual - Page 26
26
Husqvarna 326Lx Operator's manual - Page 27
27
Husqvarna 326Lx Operator's manual - Page 28
28
20 – English
MAINTENANCE
Bevel gear
The bevel gear is lled with the right quantity of grease at the
factory. However, before using the machine you should check
that the bevel gear is lled three-quarters full with grease. Use
HUSQVARNA special grease.
The grease in the bevel gear does not normally need to be
changed except if repairs are carried out.
Maintenance schedule
Below you will nd some general maintenance instructions. If
you need further information please contact your service
workshop.
Daily maintenance
1 Clean the outside of the machine.
2 Check that the components of the throttle control work
safely. (Throttle lock and throttle control.)
3 Check that the stop switch works correctly.
4 Check that the handle and handlebar are undamaged and
secured correctly.
5 Check that the cutting attachment does not rotate at idle.
6 Clean the air lter. Replace if necessary.
7 Check that the guard is undamaged and not cracked.
Replace the guard if it has been exposed to impact or is
cracked.
8 Check that the trimmer head is undamaged and not
cracked. Replace the trimmer head if necessary.
9 Check that the locking nut is tight.
10 Check that nuts and screws are tight.
11 Check that the screws that hold the bevel gear are tight.
12 Check that there are no fuel leaks from the engine, tank or
fuel lines.
Weekly maintenance
1 Check the starter and starter cord.
2 Check that the vibration damping elements are not
damaged.
3 Clean the outside of the spark plug. Remove it and check
the electrode gap. Adjust the gap to 0.5 mm or replace the
spark plug. Check that the spark plug is tted with a
suppressor.
4 Clean the cooling ns on the ywheel.
5 Clean or replace the spark arrestor mesh on the mufer
(only applies to mufers without a catalytic converter).
6 Clean the carburettor compartment.
7 Clean the cooling ns on the cylinder and check that the
air intake near the starter is not blocked.
8 Check that the bevel gear is lled three-quarters full with
lubricant. Fill if necessary using special grease.
Monthly maintenance
1 Clean the fuel tank.
2 Clean the outside of the carburettor and the space around
it.
3 Clean the fan and the area around it.
4 Check the fuel lter and the fuel hose. Replace if
necessary.
5 Check all cables and connections.
6 Replace the spark plug. Check that the spark plug is tted
with a suppressor.
7 Check and clean the spark arrestor mesh on the mufer
(only applies to mufers tted with a catalytic converter).
1
2
3
5
6
7
8
910
4
11 12
4
0,5 mm
5
6 7 8
321