Husqvarna 327HE3X Operator's Manual

Download Operator's manual of Husqvarna 327HDA65X Brush Cutter, Cutter for Free or View it Online on All-Guides.com.

Husqvarna 327HDA65X Operator's manual - Page 1
1
Husqvarna 327HDA65X Operator's manual - Page 2
2
Husqvarna 327HDA65X Operator's manual - Page 3
3
Husqvarna 327HDA65X Operator's manual - Page 4
4
Husqvarna 327HDA65X Operator's manual - Page 5
5
Husqvarna 327HDA65X Operator's manual - Page 6
6
Husqvarna 327HDA65X Operator's manual - Page 7
7
Husqvarna 327HDA65X Operator's manual - Page 8
8
Husqvarna 327HDA65X Operator's manual - Page 9
9
Husqvarna 327HDA65X Operator's manual - Page 10
10
Husqvarna 327HDA65X Operator's manual - Page 11
11
Husqvarna 327HDA65X Operator's manual - Page 12
12
Husqvarna 327HDA65X Operator's manual - Page 13
13
Husqvarna 327HDA65X Operator's manual - Page 14
14
Husqvarna 327HDA65X Operator's manual - Page 15
15
Husqvarna 327HDA65X Operator's manual - Page 16
16
Husqvarna 327HDA65X Operator's manual - Page 17
17
Husqvarna 327HDA65X Operator's manual - Page 18
18
Husqvarna 327HDA65X Operator's manual - Page 19
19
Husqvarna 327HDA65X Operator's manual - Page 20
20
Husqvarna 327HDA65X Operator's manual - Page 21
21
Husqvarna 327HDA65X Operator's manual - Page 22
22
Husqvarna 327HDA65X Operator's manual - Page 23
23
Husqvarna 327HDA65X Operator's manual - Page 24
24
Husqvarna 327HDA65X Operator's manual - Page 25
25
Husqvarna 327HDA65X Operator's manual - Page 26
26
Husqvarna 327HDA65X Operator's manual - Page 27
27
Husqvarna 327HDA65X Operator's manual - Page 28
28
MAINTENANCE
English 19
Carburettor
Your Husqvarna product has been designed and
manufactured to specifications that reduce harmful
emissions. After the engine has used 8-10 tanks of fuel
the engine will be run-in. To ensure that it continues to run
at peak performance and to minimise harmful exhaust
emissions after the running-in period, ask your dealer/
service workshop (who will have a rev counter at their
disposal) to adjust your carburettor.
Function
The carburettor governs the engine’s speed via the
throttle control. Air and fuel are mixed in the
carburettor. The air/fuel mixture is adjustable. Correct
adjustment is essential to get the best performance
from the machine.
Adjusting the carburettor means that the engine is
adapted to local operating conditions, e.g. climate,
altitude, petrol and the type of 2-stroke oil.
The carburettor has three adjustment controls:
L = Low speed jet
H = High speed jet
T = Idle adjustment screw
The L and H-jets are used to adjust the supply of fuel
to match the rate that air is admitted, which is
controlled with the throttle. If they are screwed
clockwise the air/fuel ratio becomes leaner (less fuel)
and if they are turned anti-clockwise the ratio
becomes richer (more fuel). A lean mixture gives a
higher engine speed and a rich mixture gives a lower
engine speed.
The T-screw regulates the throttle setting at idle
speed. If the T-screw is turned clockwise this gives a
higher idle speed; turning it anti-clockwise gives a
lower idle speed.
Basic setting
The basic carburettor settings are adjusted during
testing at the factory. The basic setting is richer than
the optimal setting and should be maintained for the
first few hours the machine is in use. The carburettor
should then be finely adjusted. Fine adjustment
should be carried out by a skilled technician.
CAUTION! If the blades move while the engine is idling
the T screw should be turned anti-clockwise until they
stop.
Adjustment of the idle speed
Before any adjustments are made, make sure that the air
filter is clean and the air filter cover is fitted.
Adjust the idle speed with the idle adjustment screw T, if
adjustment is necessary. First turn the idle adjustment
screw T clockwise until the blades start to move. Then
turn the idle adjustment screw T anticlockwise until the
blades stop. The idle speed is correctly adjusted when the
engine runs smoothly in every position. There should also
be a clear margin to the speed at which the blades start
to move.
The blades must also remain stationary when the choke
control is in the start throttle position.
Rec. idle speed: See the Technical data section.
Muffler
CAUTION! Some mufflers are fitted with a catalytic
converter. See chapter on Technical data to see whether
your machine is fitted with a catalytic converter.
The muffler is designed to reduce the noise level and to
direct the exhaust gases away from the operator. The
exhaust gases are hot and can contain sparks, which may
!
WARNING! If the idle speed cannot be
adjusted so that the cutting attachment
stops, contact your dealer/service
workshop. Do not use the machine until
it has been correctly adjusted or
repaired.