• Home
• Brands
• Icom Manuals
• Icom HM-195B
• Icom HM-195B Instructions Manual

Icom HM-195B Instructions Manual

Download Instructions manual of Icom HM-195B Microphone for Free or View it Online on All-Guides.com.

1

2

3

4

5

6

REMOTE-CONTROL MICROPHONE

INSTRUCTIONS q

HM-195B

HM-195SW

Thank you for purchasing the HM-195B/HM-195SW

r e m o t e -c o n t r o l m i c r o p h o n e . The COMMANDMICIV™ is

a remote control microphone for use with the IC-M423/

IC-M424, IC-M400BB, and future products.

Carefully read the instruction manual of the transceiver

you will use, before connecting and operating. These in-

structions describe only the remote-control operations.

Accessories included with the HM-195: Qty.

q Connection cable (OPC-1540*: 6 m; 20 ft) ....................... 1

w Mounting base ................................................................. 1

e Connector cap ................................................................. 1

r Microphone hanger .......................................................... 1

t Screws (M3 × 16 mm; self-tapping) ................................. 5

* The OPC-1540 has external speaker leads, as illustrated to the right.

(Yellow: Speaker (+), Black: Speaker (–))

z Supplied accessories

qwe

r

t

Yellow

Black

!8

!4

!6

!7

!5

qw ietr!0you

!1

!2

!3

q BUSY/TRANSMIT ICON (See n)

“ ➥

” appears when receiving a signal or when the

squelch is open.

“ ➥

” appears while transmitting.

w POWER ICON (See n)

“25W” appears when high power is selected. ➥

“1W” appears when low power is selected. ➥

e RX SPEAKER ICON (See ¤7)

Appears while in the RX Speaker mode.

r CHANNEL GROUP ICON (See b)

Selected channel group icons, U.S.A. “USA,” Interna- ➥

tional “INT,” Canadian “CAN,” ATIS “ATIS” or DSC “DSC”

appears, depending on the transceiver version.

“WX” appears when the weather channel is selected. ➥

t CALL CHANNEL ICON (See b)

Appears when the Call channel is selected.

y DUPLEX ICON (See b)

Appears when a duplex channel is selected.

u FAVORITE CHANNEL ICON (See ⁄3)

Appears when a Favorite (TAG) channel is selected.

i MAIL ICON (See ¤3)

Blinks when there is an unread message.

o GPS ICON

Stays ON when the GPS receiver is activated and valid ➥

position data is received.

Blinks when invalid position data is being received. ➥

!0 SWITCH ICON (See ¤5)

Appears when the “CH 16 SWITCH” in DSC Settings is set

to ‘OFF.’

!1 LOW BATTERY ICON

Blinks when the battery voltage drops to approximately 10 V

DC or less.

!2 CHANNEL NUMBER READOUT

Shows the selected operating channel number.

 •Whenasimplexchannelisselected,“A”appears.

!3 CHANNEL NAME FIELD

The channel name appears, if programmed. (See ,)

!4 KEY ICONS (See v)

Shows the programmed function of the softkeys on the front

panel.

!5 TIME ZONE INDICATOR

Shows the current time when a GPS receiver is connect- ➥

ed, or the time is manually programmed.

  •WhentheGPScurrenttimeisinvalid,“??”willblinkevery

2 seconds instead of the current time. After 23.5 hours has

passed, “NO TIME” will appear.

  •“??”willblinkevery2seconds, instead of the current time, 4

hours after the time was manually programmed. The manually

programmed time is held for only 23.5 hours, and after that,

“NO TIME” will appear.

“LOCAL” appears when the offset time is set. ➥

“MNL” appears when ➥

the time is manually programmed

.

“UTC” appears when ➥

the GGA, GLL or GNS GPS sen-

tence format is included in the GPS signal.

The date information appears when ➥

the RMC GPS sen-

tence format is included in the GPS signal.

“NO TIME” appears when no GPS receiver is connected, ➥

and no time is manually input.

!6 POSITION INDICATOR

➥ Shows the current position when a GPS receiver is con-

nected, or the position is manually programmed.

  •When the GPSposition is invalid,“??” mayblinkevery2

seconds instead of position. The last position is held for only

23.5 hours, and after that, “NO POSITION” will appear.

  •“??” will blink every 2 seconds, instead of position, 4 hours

after the position is manually programmed. The manually pro-

grammed position is held for only 23.5 hours, and after that,

“NO POSITION” will appear.

➥ “NO POSITION” appears when no GPS receiver is con-

nected, and no position is manually input.

!7 SCAN INDICATOR

“SCAN 16” appears during a Priority scan; “SCAN” ap- ➥

pears during a Normal scan. (See ⁄4)

“DUAL 16” appears during Dualwatch; “TRI 16” appears ➥

during Tri-watch. (See ⁄5)

!8 LOCAL ICON (See n)

Appears when the Attenuator function is turned ON. (

Only

U.S.A. and Australian version transceivers.)

x Function display

The HM-195 remotely controls the transceiver and provides an

Intercom function.

q DISTRESS KEY [DISTRESS] (See ⁄9)

Hold down for 3 seconds to transmit a Distress call.

w PTT SWITCH [PTT]

Hold down to transmit, release to receive. (See n)

e MENU KEY [MENU]

(

See ‹0

)

Push to enter or exit the Menu screen.

r LEFT AND RIGHT KEYS [Ω]/[≈]

Push to switch to the previous or next key function that is ➥

assigned to the softkeys. (See v)

Push to select the desired character or number in the ➥

table while in the channel name, position programming

mode, and so on. (See ,, ⁄6, ⁄7)

t ENTER KEY [ENT] (See ,, ⁄0, ⁄6)

Push to set the input data, selected item, and so on.

y

UP AND DOWN/CHANNEL SELECT KEYS [∫•CH]/[√•CH]

Push to select the operating channels, Menu items, Menu ➥

settings, and so on. (See b, ‹0)

➥

Push to check Favorite channels, change the scanning

direction or manually resume a scan. (

See ⁄4

)

u CHANNEL 16/CALL CHANNEL KEY [16/C]

Push to select Channel 16. (See ➥ b)

Hold down for 1 second to select the Call channel. ( ➥

See

b

)

  •“CALL”appearswhentheCallchannelisselected.

➥

When the Call channel is selected, hold down for 3 sec-

onds to enter Call channel programming mode . (

See m

)

i CLEAR KEY [CLEAR]

(

See ,

,

⁄6

,

‹0

)

Push to cancel the entered data, or to exit the Menu screen.

o SOFTKEYS

Desired functions can be assigned in the Menu screen.See

the transceiver’s manual for details.

!0 VOLUME AND SQUELCH SWITCH/POWER SWITCH

[VOL/SQL•PWR]

When the power is OFF, hold down for 1 second to turn ➥

ON power. (See n)

Hold down for 1 second to turn OFF power. ➥

When the power is ON, push to enter the volume level ➥

adjustment mode.* (See ⁄0)

  •Eachpushofthisswitchtogglesthemodebetweenthevol-

ume level adjustment, squelch threshold level adjustment,

operating channel selection and the LCD and key backlight

brightness adjustment, if assigned.

Rotate to adjust the volume level.* (See ➥ ⁄0)

*The desired function can be assigned in the Menu screen.

c Panel description

w

y

t

r

e

q

(Back side)

!0

o

i

y

r

u

Various functions can be assigned to the softkeys.

When a key function is assigned, the key icon is displayed

above the softkey, as shown below.

Consult your Icom dealer for details concerning which func-

tions are preprogrammed into the keys.

Softkey function selection D

When “Ω” or “≈” is displayed beside the key icon, pushing [Ω]

or [

≈] sequentially shows the previous or next key function that

is assigned to the softkey.

Push Push

*

*Push this key to start

and stop scan.

The order of the key icons may differ depending on the pre-

programming, and the contents may differ, depending on

the transceiver version.

Except for a U.S.A. and Australian version transceiver:

•[

] appears instead of [ ].

•[

] does not appear.

v Softkey function b Channel selection

Channel 16 D

Push [16/C] to select Chan- q

nel 16.

Push [CH/WX]* to return to w

the screen displayed before

you selected Channel 16,

or push [

∫

](CH) or [

√

](CH)

to select an operating channel.

Call channel D

Hold down [16/C] for 1 sec- q

ond to select the Call chan-

nel of the selected channel

group.

Push [CH/WX]* to return to w

the screen displayed before

you selected Call channel, or push [

∫

](CH) or [

√

](CH) to

select an operating channel.

* [CHAN] appears except for a U.S.A. and Australian version trans-

ceiver.

Weather channels D

(U.S.A. and Australian version transceiver only.)

Push [CH/WX] once or twice to select a weather channel. q

 •“WX”appearswhenaweatherchannelisselected.

 •“WX

” appears when the Weather Alert function is in turned

ON.

Push [ w

∫

](CH) or [

√

](CH) to select a channel.

Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France,

Spain, Russia and/or other countries. COMMANDMIC is a registered trademark of Icom Incorporated (Japan) in Japan and the United States.