• Home
• Brands
• Kenmore Manuals
• Kenmore 40289032010
• Kenmore 40289032011 Installation Manual

Kenmore 40289032011 Installation Manual

Download Installation manual of Kenmore 40289032010 Dryer for Free or View it Online on All-Guides.com. This version of Kenmore 40289032010 Manual compatible with such list of devices, as: 40289032010, 40289032011, 40289032012, 40299032010, 40299032012

1

2

Size : 420 X 297 (ram)

REMOVEPACKING MATERIAL

Cut the straps oil he carton and lift the carton off the drye*

Remove the dryer from the carton base

Check the dryer drum for all of the componen%

shown here

Literature Pack

CHECKAND CONNECTVENTING

1 Check the length of the exhaust vent it MUST NOT be longer than the

lengths shown in the chart below If it is too long, have it repaired or vented

elsewhere

2 Connect the dryer exhaust to the home exhaust system with rigid or semi

rigid metal duct DO NOT USE vinyl or foil duct for connecting the dryel

Make the transition as short as possible for best results

3 Check the exhaust hood on the outside wall Make sure it is not damaged

and that it is clear of lint buildup Make sure the damper is working properly

4 Check the exhaust for lint buildup or damage Make sure the duct is clean

and in good condition

Reeemm_ded 0 80 it 124 4 m) 41 fl (12 4 m)

_ _# 1 68 fl (207 m) 37 Jt ill 2"n)

2 5711 (]Z4 m) 33fl ri0]m)

4" (10.16 era) 3 47it (14 3 m) 29 fl (90 m)

Use only for short-run installation 0 74 it (226 m) 33 it (101 m)

1 6211 f189m) 29fl (88m)

2 51ft 1155 m) 251t 176m)

25" (6.35 ¢m) 3 41 fl (12 5 m) 21 fl (6 5 m)

CONNECT POWER CORD

For gas dryers only.

#or electric dryers proceed to step #3b on the right

Plug the dryer into a 120 VAC, 60Hz

grounded 3 prong outlet

For electric dryers only.

For gas dryers proceed to step #30 on the IdL

FOUR-WIRE POWER CORD CONNECTION

(REQUIREDinall new constructionafter Jan1,19%)

4-Wire system connections

A. External ground connector

A _ D

B. Greet, or bare copper wire of power cord

C. _f_" (]9 cm} UL listed strain relief

D. Center silver colored terminal block screw B

E

E. Neutral Grounding wire (green yellow} C J _ _ F

E Neutral wire (white or center wire}

U

i Remove the External ground connector

screw

2 Connect the ground wire (green or unwrapped} of the power cord to the

external ground connector scre_ Ifyou want to connect B(Green or bare

copper wire of power cord} to the Neutral Post without assembling with

A(cabinet ground}, call the service technician

3 Looser, or remove the center terminal block screw

4 Connect the neutral wire (white or center wire} of the power cord and the

appliance ground wire (greet, with yellow stripes} under the cenhal screw

of the terminal block

5 Connect the other wires to the outer terminal block screws Tighter, screws

B Tighten the strain relief screws

X [nsed the tab of the terminal block cover into your Dryer's rear panel slot

Secure the cover with a hold dowr, screw

THREE-WIRE POWER CORD CONNECTION

(NOT permitted in newconstructionafter Jan1,19%)

3-Wire system connections

A. External ground connector

B. Neutral grounding wire (green/yellow)

C. Cer,ter silver colored terminal block screw

D. Neuhal wire (white or center wire}

E. s/4_' (19 cm} UL listed strain relid

] Looser, or remove the center terminal block

screw

2 Connect the neutral wire (white or center wire} of the power cord to the

centel, silver colored terminal screw of the terminal block Tighter, screw

3 Connect fl:e other wires to outer terminal block screws

fighter, screws

4 Tighter, the strain relief screws

5 Insert fi:e tab of the terminal block cover into your DryeFs rear par,el slot

Secure the cover with a hold dowr, screw

CONNECT GAS SUPPLY

For gos mode_ only

1 Connect the dryer to your laundry room s gas supply using a new flexible

stainless steel connector with a 3/8" NPT fitting

Never reuse an old flex connecto_

2 Securely tighten all connections be+ween the dryer and he laundry room's

gas supply Turn on the gas supply and check all connections for leaks with

a non corrosive leak detection fluid

3/8" NPT Gas /8" NPT Pipe Plug

Connection

AGA!CSA-42ertifled

Stainless Steel Shutoff: Valve

Flexible Connector

LEVELINGTHE DRYER

1 To set the dryer to the

same height as the washel,

fully retract the leveling

feet by t_urning them coun

terclockwise, then loosen

the legs by turning them

clockwise

.evel

Leveling Feet

2 Adiust the leveling feet only as

much as necessary to level the

dryec Extending the leveling fee+

more than necessary can cause

the dryer to vibra'e

HEATERCHECK

Perform the following steps to check heater operation after

removing the literature pack and any other obiects from the

drum

1 Close the door and press the POWER button to turn oil the controls

2 Rotate the CYCLE SELECTOR KNOB to select a hea'ed cycle, such as

NORMAL.

3 Press the START/PAUSE button to start the cycle

After approximately one minute, open the door and check for hea" if no

heat is felt after approximately 2 minutes, consuft the troubleshooting sec

tion of the owner's manual

FINAL CHECKS

Use the following checklist to ma ke sure you have complet

ed all of the installation steps

INSTALLATION STEP

1 - REMOVE PACKING MATERIAL

2 - CHECK AND CONNECT VENTING

3 - CONNECT POWER CORD

4 - CONNECT GAS SUPPLY (For gas models only)

5- LEVEL THE DRYER

6 - HEATER CHECK

Screws

For more information, refer to Installation Instructions included in the pedestal

For accessory installation instructions, consult the ins:allafion instructions

included with each accessory

LP CONVERSION KiT

SiDE VENT KIT - DV ]A XAA

STACKING KIT- SK 5AXAA

Test for proper operation by running the dryer through a

complete cycle.

Please consult your owner's manual for complete details.

P/No. DC68-O289gA-O1