Lab.gruppen LAB 1300C Specifications
Download Specifications of Lab.gruppen LAB 1300C Amplifier for Free or View it Online on All-Guides.com.
1
LAB 1300C Specification
MAX OUTPUT POWER
1)
8
Ω
stereo
4
Ω
stereo
2
Ω
stereo
2)
8
Ω
bridged
4
Ω
bridged
FTC
20 Hz-20 kHz
at 0.1% THD
325 W
600 W
800 W
1300 W
1560 W
EIA
1 kHz
at Cliplevel
350 W
650 W
900 W
1400 W
1800 W
IHF
Peak Power
20 ms burst
385 W
750 W
1000 W
1500 W
2000 W
SPEAKER PROTECTION
Each channel is fuse protected on the positive and negative power supply rails. Electronic short-circuit protection with a progressive characteristic. The output power is turned off at shorted
output. The output power is turned off at shorted output. The power amplifier can be run into short-circuits for a long time without damage, and is open circuit and mismatch proof.
DISTORTION
THD 20 Hz-20 kHz and 1 W-600 W
THD at 1kHz and 600W
DIM 30 at 300 W
CCIF (13 and 14 kHz) at 200 W
SMPTE (60 Hz and 7 kHz) at 300 W
POWER BANDWIDTH
3)
Slew rate
OUTPUT IMPEDANCE
HUM AND NOISE below max power
CHANNEL SEPARATION
PHASE AND DELAY
Deviation from perfect delay
Total delay input to output at 4 ohms
INPUTS
Sensitivity, switchable for full output into 4 ohms
Gain, switchable
Impedance
Common mode rejection at 1 kHz
FRONT PANEL
Gain controls
Output display
Temp indicator
VHF indicator
On indicator
REAR PANEL
Input connectors
Output connectors
Switches:
Gain
Link
Rev B
Clip limiter A and B
POWER
Operation voltage
Minimum start voltage
Full output power
Peak inrush current
OVERALL DIMENSIONS
mm (inch)
WEIGHT
APPROVALS
1) Specifications measured with 230 V regulated AC
2) Continuous power, one channel driven or peak power
both channels driven. (Thermal protection may occur
at high continuous power).
LAB. GRUPPEN reserve the right to alter functions or
specifications without prior notice.
4 ohms
4 ohms
4 ohms
4 ohms
4 ohms
1 kHz
1 kHz
10 kHz
150 Hz-20 kHZ
(2) red + (10) green LED´s
(2) yellow LED´s
(2) yellow LED´s
(2) green LED´s
CE
0.08 %
0.03 %
0.02 %
0.02 %
0.05 %
5 Hz-50 kHz
40 V/
µ
s
0.07 ohm
<- 105 dBA
80 dB
70 dB
± 2
°
4,1
µ
s
0.775 or 1,8 Vrms
37 dB or 29 dB
20 kohms, balanced
50 dB
(2) Channel A - B
Fast peak - slow release
80_ C at heatzink
> 10 kHz at full power
DC rail voltage for channel A and B
(2) XLR type 3 pin female (pin 2+), and (2) 1/4
″
jack
(2) Neutric 4-pole speakon connectors (pin 1+ output)
37 dB or 29 dB
Tandem mono, channel A and B
Phase reverse of channel B
On - Off
Option
120 V - 270 V AC 65 V-135 V AC
190 V AC 95 V AC
180 V -260 V AC 90 V-130 V AC
4.5A
483 (19
″
) W
×
88 (3.5
″
) H
×
310 (12.4
″
) D
8 kg (18 lbs)
Emission EN 55 103-1, E3
Immunity EN 55 103-2, E3, with S/N below 1% at normal operation level
4)
Safety EN 60 065, class I
3) The VHF-protection turns off the channel for frequencies
above 20 kHz at full power.
4) Normal operation level 1/8 of full power or –9dB below clip point.
LAB.GRUPPEN AB ANDERSSON & BÄVHOLM
Gullregnsvägen 16, 434 44 KUNGSBACKA,
SWEDEN
Telephone +46 300 168 23 FAX +46 300 142 46