LEXICON 20 - QUICK REFERENCE GUIDE REV 2 Quick Reference Manual
Download Quick reference manual of Lexicon 20 - REV 2 Power Supply for Free or View it Online on All-Guides.com.
Brand: Lexicon
Category: Power Supply
Type: Quick reference manual
Model: Lexicon 20 - REV 2 , Lexicon 20 AD - REV 2
Pages: 2
1
2
20/20 AD Quick Reference Guide
© 1994
070-09091 Rev 2
ALT-ATTEN will mute the out-
puts. The level meters will still
work.
Alternate Modes
When the compressor is
OFF, the behavior of the level
meters is determined by set-
tings of 1 dB SCALE and PK
HOLD.
Press 1dB SCALE to select
1dB scale on level meters.
Press PK HOLD to cause the
level meters to hold at the
highest level received.
none
1 dB SCALE
DISPLAY
Normal
1 dB Scale
Gain Reduction
Normal
1 dB Scale
Gain Reduction
none
1 dB SCALE
DISPLAY
Normal
Normal
Normal
(Blank)
1 dB Scale
Gain Reduction
Switches ON Meters 1 & 2 Meters 3 & 4
4-Channel
Mode
2-Channel
Mode
1dB SCALE
GAIN
REDUCTION
NORMAL
OVL
0
-1
-2
-3
-4
-5
-6
-7
-8
-9
1
2
3
4
5
6
7
8
9
10
11
OVL
0
-3
-6
-12
-18
-24
-30
-36
-42
-60
- red -
- red -
- yellow -
- yellow -
- green -
- green -
- green -
- green -
- green -
- green -
- green -
OVL
0
3
6
12
18
24
30
36
42
60
When the compressor is ON, pressing DISPLAY will cause gain
reduction (in dB) to be displayed on the right two meters (2-
channel mode) or on all four meters (4-channel mode).
In 4-channel mode, ALT-LINK
activates a synchronized short
tone burst.
ALT-DITHER activates psy-
choacoustically optimized
noise shaping. (Disables 4-
channel mode, compression
and mute functions.)
ALT-4 CHAN activates output
of a digital sinewave at the
AES ports.
ALT-DISPLAY activates remote
mode/front panel lockout. When
activated, the 1dB SCALE and
DISPLAY LEDs flash and front
panel controls are locked into
their current settings.
1dB SCALE
ALT
4 CHAN
~
DISPLAY
RMT
LINK
press and hold ...then press one of these.
To activate
the alternate modes...
ATTEN
MUTE
ON
VID
Repeat to exit the alternate mode.
DITHER
EXT SYNC
Getting Started
Input Connections
Balanced Unbalanced
pin Screen Screen and
1 (Shield) Return
pin Positive Positive
2 Polarity Polarity
pin Return Open or
3 Return
Make sure the rear panel
BALANCE switches are set
to match the type of input.
(IN = unbalanced; OUT =
balanced) The red UNBAL
light will indicate an error if
there is a mismatch.
EXT SYNC allows you to syn-
chronize to an internally de-
rived sample clock, or to an
external AES or Word Clock
signal in the range of 41-
51kHz.
ATTEN reduces input level by
6dB. Use sparingly, and only
on balanced input signals.
Note: The Word Clock input is
not transformer-isolated, and re-
quires a ground connection be-
tween the 20/20 AD and the sig-
nal source.
Note: Non-linearity of the poten-
tiometer can cause the signal to
become unbalanced when the
level knob is set to 11:30. To
correct this, turn the knob slightly
in either direction until the UN-
BAL light goes out.
Dither types vary in spectral
distribution of noise:
WIDE produces white noise
HF produces noise whose
amplitude is lower than WIDE
at low frequencies, but higher
at high frequencies.
20 BIT has the same spectrum
as HF, but with lower ampli-
tude. Use this setting when
recording to 20-bit media.
Level Meters
Before switching between Internal and External modes, be
sure to reduce monitor volume, as some D/A converters do
not mute when they lose lock.
20/20 AD
POWER
20 BIT A/D CONVERTER
1dB SCALE
ALT
PK HOLD
ATTEN
1
THRESHUNBAL THRESHUNBAL
2 3
THRESHUNBAL THRESHUNBAL
4
4 CHAN
~
EMPH
OVL
0
3
6
12
18
24
30
36
42
60
OVL
0
3
6
12
18
24
30
36
42
60
DISPLAY
RMT
LINK
ON
6
GAIN
8
10
12
4
2
0
-14
-10
0-36
-18
-22
-26
100
mS
THRESHOLD RELEASE
DITHER
FORMAT
AES / WC:
SAMPLE RATE
EXT SYNC
DIGITAL COMP/LIMITER
-6
M
C
P
1S10
0
+
•
–
MUTE
∞
VID
+
•
–
M
C
P
WIDE
HF
48
AES
WC
PRES
20BIT
PL DN
44.1
SPDIF
AES
LOCK
ALT-EXT SYNC enables the
digital audio input.
ALT-ON is reserved for future enhancements.