LEXICON 300 V3.0 - QUICK REFERENCE GUIDE REV 1 Quick Reference Manual

Download Quick reference manual of Lexicon 300 V3.0 - GUIDE REV 1 Processor for Free or View it Online on All-Guides.com.

Lexicon 300 V3.0 -  GUIDE REV 1 Quick reference manual - Page 1
1
Lexicon 300 V3.0 -  GUIDE REV 1 Quick reference manual - Page 2
2
300 V 3.0 Quick Reference Guide
300
DIGITAL EFFECTS SYSTEM
MIDI
48 kHz
44.1 kHz
32 kHz
CONTROL
UP
PAGE
DOWN
7 89
456
123
—0
ENTER
PAGE
SETUP
SELECT
MACH
STORE
VALUE
SETUP
EDIT
EFFECT
EDIT
MOD
EDIT
BYPASS
A
BYPASS
B
POWER
LEVEL
Once you have made changes to an Effect, remember that
you must not only store those changes in Effect Edit mode,
but also must store the Setup in which the Effect is loaded.
Note:
If the 300 Copy Tools function is set to DISABLE, no STORE
functions can be performed.This function is enabled in CNTRL mode.
(Selection of CNTRL does not interrupt audio operation of the 300.)
Storing your changes
Editing an Effect
Single Setup Presets
P118 Stairwell
P119 *Hangar
P120 MarbleFoyer
P121 EarlyReflect
P122 Lecture Hall
P123 *CarInterior
P124 Score Stage
P125 Gate It!!
P126 *Rich Plate
P127 Glossy Plate
P128 Warm Plate
P129 Perc Plate
P130 Contem-Plate
P131 *EKO Plate
P132 Bright Plate
P133 *Round Plate
P134 StereoAdjust
P135 Phase Invert
P136 2 Frame Dly
P137 3 Frame Dly
P138 4 Frame Dly
P139 MS Decode
P140 *MultiEchoes
P141 LFO Panner
P142 Telephone
P143 *Stereo Shift
P144 Octave Down
P145 Vox Chorus
P146 Pole Flange
P147 Bulkie Roll
P148 Heavy Roll
P149 *Going, Going
P150 Zorch!
P101 Large Hall
P102 Medium Hall
P103 Small Hall
P104 *Church
P105 *Rooms
P106 RehursalRoom
P107 *Chamber
P108 LiveDrumRoom
P109 *Studio A
P110 *Studio B
P111 *Brick Wall
P112 *Deep End
P113 Oil Tanker
P114 *Synth Hall
P115 Dance Hall
P116 *Ambience
P117 In A Room
Setup Selection
The Setup Presets are or-
ganized as follows:
101-150 = Single Setups
201-225 = Dual Mono Setups
301-325 = Cascade Setups
To simplify the choice
among the many possible
effect and system routings,
the 300 is shipped with 100
Setup Presets.
The 300 is organized into Setups and Effects. Setups are
collections of many decisions, including DSP routing (single or
split), Input levels, Source, Balances, LFO Rate and Shape,
and one (or two) Effects. These decisions are grouped to-
gether, named, and stored so they can be called up with a
single user action.
V3.0 Setups
The 300 V3.0 factory default state is: Analog In; 48kHz sampling rate.
Single Setups
All Single Setup Presets are
factory loaded with an Effect
of the same name. (The Ef-
fect number may
not
be the
same.)
Single Setups unify both
Machine A and Machine B
into a single DSP engine.
An asterisk (*) in a Preset
name indicates that one or
more parameters are
patched to the Soft knob.
Turn the Soft knob to in-
crease or decrease the pa-
rameter value.
Press VALUE to alternate
between a display of pa-
rameter names and a dis-
play of their values.
L
R
Analog
Digital
Analog
Level
Analog
Balance
Σ
L
R
Digital
Level
Digital
Balance
Σ
Overall
Mix
Dry
Dry
Analog and
Digital Out
Effect
Edit A
Press SETUP SELECT,
then use the Soft knob to
select a Setup Preset.
When you have found a Pre-
set you want to load, press
ENTER.
Press
PAGE UP to display
any Soft knob patches
made to Setup Effect para-
meters; press VALUE to
show the parameter values.
Press EFFECT EDIT .
Press the buttons above or
below a parameter label to
select it.
Press PAGE DOWN to view
additional parameter pages;
press EFFECT EDIT to re-
turn to the main edit screen.
From Effect Edit mode,
press STORE . Turn the
Soft knob to find an avail-
able register, then press
STORE again.
From Setup Edit mode,
press STORE . Turn the
Soft knob to find an avail-
able register, then press
STORE again.