Lorex QLR464 Quick Setup Manual
Download Quick setup manual of Lorex QLR464 DVR, PCI Card for Free or View it Online on All-Guides.com.
1
2
QUICK SETUP GUIDE
Skill Level
Intermediate
easy
advanced
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Skill Level
Intermediate
easy
advanced
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Time: 20 Minutes
Hand Tools Skills - Moderate
PCI CARD INSTALLATION GUIDE
BASIC SETUP: PCI CARD
STEP 1
EXPRESS INSTALLATION
(DRIVER AND LOCAL SOFTWARE)
STEP 3
Installing the PCI Card Driver
Skill Level
Intermediate
easy
advanced
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Skill Level
Intermediate
easy
advanced
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Time: 20 Minutes
Hand Tools Skills - Easy
CAMERA INSTA L L AT IO N G U I D E
BASIC SETUP: CAMERAS
STEP 2
It’s all on the Web www.lorexcctv.com
For detailed setup information, please refer to your included User’s
Manual. For additional information, please visit our website
www.lorexcctv.com
Infor mation in this document is subject to change without notice. As our products are subje ct to
continuous improvement, Lorex Technology INC. and our subsidiaries reserve the right to modif y
product design, specifications and prices, without notice and without incur ring any obligation. E&OE
© 2010 LOREX . All rights reser ved.
LO CA L I N S TA LL ATION GUIDE
Time: 10 Minutes
Hardware
PC
4 PORT PCI CARD
DIGITAL VIDEO RECORDER
QLR460 SERIES
ENGLISH REVISION # R1
NOTE:
QLR464 also includes:
4 x Cameras
4 x 60ft Extension Cables
1 x 4-in-1 Power Adaptor
PACKAGE CONTENTS:
1 x 4 Port PCI Capture Card
1 x User’s Manual
1 x Quick Start Guide
1 x Software CD
Skill Level
Intermediate
easy
advanced
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Skills - Easy
Hardware Installation
NOTE: Please turn off the computer’s power and unplug the power cord
prior to installing the QLR Capture Card.
If you are unfamiliar with installing PC hardware, it is recommended to
have a PC technician perform the installation.
1
Remove the computer’s cover panel
Refer to your computer’s owner’s
manual for instructions on how
to remove the case cover if you
are unsure of how to do so.
2
Remove the PCI cover plate
Remove the PCI slot’s metal
plate at the back of the system.
Be careful of
sharp edges
while removing
the metal plate.
3
Insert the PCI card
Push the card firmly into an avail-
able PCI slot until it clicks in place.
The gold-colored connector pins
should not be visible after the card
is secure.
4
Secure the PCI card
Secure the PCI Card by tightening
the screw with a screw driver.
5
Replace the computer’s cover panel
5. Slide the computer cover panel
back on and secure it with screws
using a screw driver.
Congratulations!
You have completed Step 1 successfully.
Your computer can now support up to 4 cameras.
Congratulations!
You have successfully installed the VistaPro 6 Server software.
You can now view, record and playback video on your local computer.
Camera Installation
Before you install a camera, carefully plan where and how you will
position the camera, and where you will route the cables.
NOTE: The 4 Port PCI card has 4 Video inputs, allowing you to
connect up to 4 cameras (the instructions below apply to the
cameras included with QLR464). You may connect your own
cameras, however please make sure to use a proper power adaptor
NOT EXCEEDING 12V DC for each camera.
1
Connect to BNC extension cable
Connect the camera’s BNC
connector into the extension cable’s
BNC connector. The connection
should be snug and secure.
2
Connect power cable
Plug the camera’s power connector
into the power connector end of the
extension cable.
3
Connect BNC to the computer
Screw in the BNC connector from
the extension cable to the back
of the QLR card. The connection
should be snug and secure.
4
Connect power adaptor
Connect the 4-in-1 12V DC power
adaptor to the power connector end
of the extension cable.
5
Connect additional cameras
Repeat these steps for up to three
additional cameras.
6
Plug in the power adaptor
Plug the power adaptor into the wall
outlet. This will provide power for
up to 4 cameras.
For QLR464, you are required to use the
included power adaptor. Use of a non-regulated,
nonconforming power adaptor can damage the
cameras and will void the warranty.
WARNING
Make sure your
cameras are fully
functional before
mounting them in
the final location.
TIP
Logging In to VistaPro 6 Server
Click the DVR shortcut on your desktop , or locate the application
in the start menu. If a Windows Firewall warning pops up, select the
“Unblock” option.
8
NOTE: Click the Virtual Keyboard button to type in the User ID and Password if you do
not have access to a keyboard.
NOTE: It is recommended to change the default password. For details on changing the admin
password, see “Changing User Account Password” on page 34.
NOTE: Click the Exit button on the bottom right hand corner of the window to exit the program.
Under ID, enter admin; under Password, enter 1111. Click the
checkmark button
to log in.
10
If your system does not support
auto-run, you can browse the CD,
and search for the Vista Pro 6
Server in the X:\Package\Remote
Client directory, where “X” is your
CD/DVD drive.
Follow the auto-run
instructions on screen. Click
on the “Run SetupDisc.exe”
option if prompted.
2
Note: A pop-up window may
appear asking you to verify the
software. Click the button to
allow the installation.
The installation screen will
open. Click on the Install
button and then click the
Express installation button.
3
The installation window
will pop up. Follow the
instructions by clicking the
“Next” buttons after making
your selections. You will be
asked to set the installation
location, language and
program folder.
4
Note: It is recommended that
you select “automatically”. This
ensures that your DVR is always
ready to record, even after
restarting your computer.
Once installed, you will be
asked to select whether you
want the program to start
automatically or manually.
5
Note: If you set more than 90% of
your hard drive to be allocated to the
QLR460 storage, your computer may
read the drive as being full, as this
hard drive space is being saved for the
program.
You will be asked to select a
drive for storage, and to set
the storage size.
6
It is recommended that you remove the installation CD and then
restart your computer before running the VistaPro 6 Server Software.
7
Insert the installation disc into your
computer’s CD/DVD drive.
1
Click the Lock Button . The Logon window appears.
9
Default ID: admin
Default Password: 1111
EXPRESS INSTALLATION
(DRIVER AND LOCAL SOFTWARE)
CONTINUED
STEP 3