Marley Engineered Products 7100 Important Safety Instructions Manual

Download Instruction manual of Marley Engineered Products 7100 Fan for Free or View it Online on All-Guides.com. This version of Marley Engineered Products 7100 Manual compatible with such list of devices, as: 7130, 763, 768IC, 8090, 8100

Marley Engineered Products 7100 Instruction manual - Page 1
1
Marley Engineered Products 7100 Instruction manual - Page 2
2
Marley Engineered Products 7100 Instruction manual - Page 3
3
Marley Engineered Products 7100 Instruction manual - Page 4
4
Marley Engineered Products 7100 Instruction manual - Page 5
5
Marley Engineered Products 7100 Instruction manual - Page 6
6
Marley Engineered Products 7100 Instruction manual - Page 7
7
Marley Engineered Products 7100 Instruction manual - Page 8
8
Marley Engineered Products 7100 Instruction manual - Page 9
9
Marley Engineered Products 7100 Instruction manual - Page 10
10
Marley Engineered Products 7100 Instruction manual - Page 11
11
Marley Engineered Products 7100 Instruction manual - Page 12
12
Marley Engineered Products 7100 Instruction manual - Page 13
13
Marley Engineered Products 7100 Instruction manual - Page 14
14
Marley Engineered Products 7100 Instruction manual - Page 15
15
Marley Engineered Products 7100 Instruction manual - Page 16
16
Marley Engineered Products 7100 Instruction manual - Page 17
17
Marley Engineered Products 7100 Instruction manual - Page 18
18
Marley Engineered Products 7100 Instruction manual - Page 19
19
Marley Engineered Products 7100 Instruction manual - Page 20
20
Marley Engineered Products 7100 Instruction manual - Page 21
21
Marley Engineered Products 7100 Instruction manual - Page 22
22
Marley Engineered Products 7100 Instruction manual - Page 23
23
Marley Engineered Products 7100 Instruction manual - Page 24
24
READ AND SAVE THESE INSTRUCTIONS
MODELS 761, 763, 765, 7100, 7130, 7150,
8090 & 8100 FANS
MODELS 768IC, 770IC, 7100L, 7150L, 7100FL, 7150FL,
8090L & 8100L FAN/LIGHTS
MODELS 7100H, 7100FLH, 7150H & 7150FLH
FANS & FAN/LIGHTS with HUMIDITY SENSOR
DESCRIPTION
The FAN and FAN/LIGHT models listed in these instructions
are intended for use in bathrooms. However, they can also be
used in other areas where ventilation is required. These units
are approved for installation in the ceiling above a bathtub or
shower stall only when connected to a U.L. Listed GFCI pro-
tected branch circuit. ALL FAN/LIGHT models are U.L. Listed
Type I.C. (Inherently Protected) for installation in insulated ceil-
ings.
UNPACKING
Unpack carefully. If there are missing components or hidden
damage, immediately contact your distributor or the delivering
carrier concerning discrepancies.
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
TO REDUCE RISK OF FIRE, ELECTRICAL SHOCK OR
INJURY TO PERSONS, OBSERVE THE FOLLOWING:
1. Do not use this fan with any Solid-State speed control
device.
2. Use this unit only in the manner intended by the manufa-
cturer. If you have any questions, contact the
manufacturer.
3. Before servicing or cleaning unit, switch power off at
service panel and lock service panel to prevent power
from being switched on accidentally.
4. Installation work and electrical wiring must be done by
qualified person(s) in accordance with all applicable
codes and standards, including fire-rated construction.
5. Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of fuel
burning equipment to prevent back drafting. Follow the
heating equipment manufacturer’s guideline and safety
standards such as those published by the
National Fire Protection Association (NFPA), and the
American Society for Heating and Air Conditioning
Engineers (ASHRAE), and the local code authorities.
6. When cutting or drilling into wall or ceiling, do not damage
electrical wiring or other hidden utilities.
7. Ducted fans must always be vented to the outdoors.
8. If this unit is installed over a tub or shower, it must be
marked as appropriate for the application. See product
label.
9. NEVER place a switch where it can be reached from a tub
or shower.
10. CAUTION: For General Ventilation Use Only! Do not
use to exhaust hazardous or explosive materials or vapors.
11. Not for use in kitchens.
TOOLS
Installation of your Marley Engineered Products fan is easy. No
special technical knowledge is needed; only a few ordinary
tools are required:
Screwdriver
Hammer
Saber saw, Keyhole saw, or Jig saw
Electric drill with bit
Wire cutters
Wire stripper
Wire nuts and general electrical supplies
Safety glasses
Ruler and straight edge
All hand tools should be insulated. Power tools should display
the UL Listing Mark.