Maytag 8113P644-60 Owner's Manual

Download Owner's manual of Maytag 8113P644-60 Ranges for Free or View it Online on All-Guides.com.

Brand: Maytag

Category: Ranges

Type: Owner's manual for Maytag 8113P644-60

Pages: 16

Download Maytag 8113P644-60 Owner's manual

Maytag 8113P644-60 Owner's manual - Page 1
1
Maytag 8113P644-60 Owner's manual - Page 2
2
Maytag 8113P644-60 Owner's manual - Page 3
3
Maytag 8113P644-60 Owner's manual - Page 4
4
Maytag 8113P644-60 Owner's manual - Page 5
5
Maytag 8113P644-60 Owner's manual - Page 6
6
Maytag 8113P644-60 Owner's manual - Page 7
7
Maytag 8113P644-60 Owner's manual - Page 8
8
Maytag 8113P644-60 Owner's manual - Page 9
9
Maytag 8113P644-60 Owner's manual - Page 10
10
Maytag 8113P644-60 Owner's manual - Page 11
11
Maytag 8113P644-60 Owner's manual - Page 12
12
Maytag 8113P644-60 Owner's manual - Page 13
13
Maytag 8113P644-60 Owner's manual - Page 14
14
Maytag 8113P644-60 Owner's manual - Page 15
15
Maytag 8113P644-60 Owner's manual - Page 16
16
ABOUT SERVICE
14
S Do not attempt to service this appliance yourself
unless directed to do so in this manual or the chart
below. Refer all other servicing to a qualified servicer
or call us at 1-800-688 -9900.
S Locate and mark circuit breaker or fuse. Never
replace a blown fuse or reset a circuit breaker until
you know what caused the problem. Always replace
a blown fuse with one of the correct amperage, do
not use a substitute.
S Always disconnect power to unit before any servicing
by tripping circuit breaker to the OFF position or by
removing the fuse.
CAUTION
Burner flame is uneven. a. clogged burner port(s) a. clean ports with straight pin
Baking results are not
satisfactory.
browning is too pale, too dark or
is uneven.
food cooks unevenly.
food is underdone or
overdone.
a. oven not preheated or set at correct
temperature.
b. used incorrect rack position
c. incorrect use of aluminum foil
d. oven bottom incorrectly replaced
e. oven thermostat sensing device is
out of the holding clip(s).
a. preheat oven 8 to 15 minutes
b. see page 13
c. see page 7
d. replace oven bottom correctly
e. reinstall thermostat sensing device
TROUBLESHOOTING CHART
PROBLEM
Surface burner fails to light.
CAUSE
a. power supply not connected
b. air in the gas line
c. clogged burner port(s)
d. surface control not completely
turned to the LITE position or turned
too quickly from the LITE position
e. power failure (pilotless ignition)
CORRECTION
a. connect power, check circuit
breaker or fuse box
b. see page 5 for instructions on
bleeding air from the gas line
c. clean ports with straight pin or small
metal paper clip
d. turn control to the LITE position until
the burner ignites, then turn control
to desired flame size
e. see page 5 to light burner during a
power failure
Surface burner flame lifts off port
or is yellow in color.
Oven burner fails to light.
a. air/gas mixture not proper
NOTE: Some yellow tipping with LP
gas is normal and acceptable.
a. power supply not connected
b. power failure
c. oven incorrectly set
a. call serviceman to adjust burner
NOTE: Be sure installer properly
adjusted range at time of installation.
a. connect power, check circuit
breaker or fuse box
b. oven will not operate during a power
failure
c. See page 7
Popping sound heard when
burner extinguishes.
This is a normal sound that occurs with some types of gas when a hot burner is
turned off. The popping sound is not a s afety hazard and will not damage the
appliance.