• Home
• Brands
• Maytag Manuals
• Maytag GGG388LXB03
• Maytag MGT8655XS03 Installation Instructions Manual

Maytag MGT8655XS03 Installation Instructions Manual

Download Installation instructions manual of Maytag GGG388LXB03 Cooktop for Free or View it Online on All-Guides.com. This version of Maytag GGG388LXB03 Manual compatible with such list of devices, as: GGG388LXB03, MGT8655XB02, MGT8655XS03, MGT8655XW02, MGT8655XW03

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

3. Turn the Number 0.054 Natural gas broil burner orifice hood

counterclockwise to remove.

3. Using a Phillips or Torx_)screwdriver, remove the burner base.

A .........

, _F"_ ...........

B ................................._

__ :"1 _- .......................................................E

4=

A

/

A. Number 0.054 Natural gas broil burner orifice hood

Install the green Number 0.037 LP gas broil burner orifice

hood, turning it clockwise 4 or 5 turns. Do not overtighten.

...., .......

4=

A. Burner cap

B. Gas tube opening

C. Burner base screws

D. Burner base

Apply masking tape to the end of a %2" (7.0 mm) nut driver to

help hold the Natural gas orifice spud in the nut driver while

changing it. Press nut driver down onto the Natural gas orifice

spud and remove by turning it counterclockwise and lifting

out. Set the Natural gas orifice spud aside.

A

9

A. Number 0.037 LP gas broil burner orifice hood

5. Place the broil burner on the broil burner orifice hood. Insert

the broil burner Iocator pin in the hole in the oven back.

6. Position the broil burner against the roof of the oven cavity

and attach with screw.

A B

A. Broil burner orifice hood

B. Broil burner

To Convert Surface Burners

1. If the burner grates are installed, remove them.

2. Remove the burner caps.

A. Natural gas orifice spud

Use the following chart for correct LP gas orifice spud for each

burner. Refer to the model/serial rating plate behind the control

panel for proper sizing of LP gas orifice spuds for each burner

location.

LP Gas Orifice Spud Chart

Burner Rating Color Number

4,000 BTU Blue 64L

7,000 BTU Black 81L

9,100 BTU Green 97L

14,000 BTU Red 114L

5. Replace the Natural gas orifice spud with the correct LP gas

orifice spud. See the "LP Gas Orifice Spud Chart."

6. Replace burner base and hand tighten the screws.

7. Replace burner cap.

8. Repeat steps 1 through 7 for the remaining burners.

9. Place Natural gas orifice spuds in plastic parts bag for future

use and keep with literature package.

10. Replace burner grates.

11. Complete installation. See "Make Gas Connection" and

"Electronic Ignition System" sections.

Checking for proper cooktop burner flame is very important.

The small inner cone should have a very distinct blue flame

1¼.to 1/2"long. The outer cone is not as distinct as the inner

cone. LP gas flames have a slightly yellow tip.

IMPORTANT: You may have to adjust the "LO" setting for

each cooktop burner. See "Adjust Flame Height" in the

"Electronic Ignition System" section.

14