Maytag 3395316 Installation Instructions Manual

Download Installation instructions manual of Maytag 3395316 Dryer for Free or View it Online on All-Guides.com.

Brand: Maytag

Category: Dryer

Type: Installation instructions manual for Maytag 3395316

Pages: 12

Download Maytag 3395316 Installation instructions manual

Maytag 3395316 Installation instructions manual - Page 1
1
Maytag 3395316 Installation instructions manual - Page 2
2
Maytag 3395316 Installation instructions manual - Page 3
3
Maytag 3395316 Installation instructions manual - Page 4
4
Maytag 3395316 Installation instructions manual - Page 5
5
Maytag 3395316 Installation instructions manual - Page 6
6
Maytag 3395316 Installation instructions manual - Page 7
7
Maytag 3395316 Installation instructions manual - Page 8
8
Maytag 3395316 Installation instructions manual - Page 9
9
Maytag 3395316 Installation instructions manual - Page 10
10
Maytag 3395316 Installation instructions manual - Page 11
11
Maytag 3395316 Installation instructions manual - Page 12
12
If dryer Is Installed In a confined area
such as a bedroom, bathroom or
closet, it must be exhausted to the
outside and provision must be made
for enough air for combustion and
ventilation. (Check governing codes
and ordinances. Also refer to the
“Recessed area and closet installation
instructions, - Page 8.)
An
exhaust hood
should cap the
exhaust duct to prevent exhausted air
from returning into the dryer. The
outlet hood must be at least 12 inches
from the ground or any object that
may be in the path of the exhaust.
Four-Inch outlet hood Is preferred.
However, a 2.l/2-inch outlet exhaust
hood may be used. (A 2-l/2-inch
outlet creates greater back pressure
than other hoods.)
A maln exhaust duct
can be used for
exhausting a group of dryers. Main
exhaust duct should be sized to
remove 200 CFM of air per dryer.
Large-capacity lint screens of proper
design may be used in the main
exhaust duct if checked and cleaned
frequently. The room where the dryers
are located should have make-up air
equal to or greater than the CFM of
all the dryers in the room.
Back-draft damper kit
(Part No.
3391910) should be Installed in each
dryer exhaust duct to prevent
exhausted air from returning into the
dryers and to keep the exhaust
balance within the main exhaust
duct. Unobstructed air openings are
required.
Each exhaust duct
should enter the
main duct at an angle pointing in the
direction of the airflow. Ducts
entering from the opposlte side
should be staggered to reduce the
exhausted air from interfering with the
other ducts.
The
maxlmum angle
of each duct
entering the main duct should be no
more than 30”.
Product Damage
Keep alr openlngs free of dry-
cleaning fluld rumes.
Fumes create acids which, when
drawn through the dryer heating
units, can damage dryers and
loads being dried.
A
clean-out cover
should be located
on the main exhaust duct for
periodically cleaning the exhaust
system,
An
exhaust hood
should cap the
outside end of the main duct to
prevent exhausted air from returning
to the dryers. If an exhaust hood
cannot be used, the outside end of
the main duct should have a sweep
elbow directed downward. If the
main duct travels vertically through
the roof rather than through the wall,
install 180” sweep elbow on the end
of duct at least 2 feet above the
highest part of the building. The
opening wall or roof shall have a
diameter l/2 inch larger than the
exhaust duct diameter. The exhaust
duct should be centered in the
opening.
exhaust hood
or sweep
elbow
horlrontal duct
2 1. mln.
highest polnt of
bulldlng
\
Do Not install screening cap over end
of duct.
Exhaust duct
connection
Electrlcal Shock Hazard
Dlxonnect both power supply
cords before maklng these
changes.
Failure to do so may result In
electrlcal shock or personal Injury.
I
Determine which direction you need
to attach the exhaust ducts to the
dryer. Dryer can be exhausted
straight out the back or from the right
or left side or through bottom.
Next, determine the length of exhaust
duct you will need to connect the
dryer to exhaust hoods or the main
exhaust.
To connect exhaust duct
straight out the back-
Attach exhaust duct to dryer duct.
Then connect exhaust duct to
exhaust hood or main exhaust. Use
duct tape to seal all joints.
Page 6