Maytag W10096988A Installation Instructions Manual

Download Installation instructions manual of Maytag Cabrio,- WED5500X Dryer for Free or View it Online on All-Guides.com. This version of Maytag Cabrio,- WED5500X Manual compatible with such list of devices, as: Cabrio,- WED5500X, Cabrio,- WED5550X, MEDX500XW, MEDX550XW, WED5500XW

Maytag Cabrio,- WED5500X Installation instructions manual - Page 1
1
Maytag Cabrio,- WED5500X Installation instructions manual - Page 2
2
Maytag Cabrio,- WED5500X Installation instructions manual - Page 3
3
Maytag Cabrio,- WED5500X Installation instructions manual - Page 4
4
Maytag Cabrio,- WED5500X Installation instructions manual - Page 5
5
Maytag Cabrio,- WED5500X Installation instructions manual - Page 6
6
Maytag Cabrio,- WED5500X Installation instructions manual - Page 7
7
Maytag Cabrio,- WED5500X Installation instructions manual - Page 8
8
Maytag Cabrio,- WED5500X Installation instructions manual - Page 9
9
Maytag Cabrio,- WED5500X Installation instructions manual - Page 10
10
Maytag Cabrio,- WED5500X Installation instructions manual - Page 11
11
Maytag Cabrio,- WED5500X Installation instructions manual - Page 12
12
Maytag Cabrio,- WED5500X Installation instructions manual - Page 13
13
Maytag Cabrio,- WED5500X Installation instructions manual - Page 14
14
Maytag Cabrio,- WED5500X Installation instructions manual - Page 15
15
Maytag Cabrio,- WED5500X Installation instructions manual - Page 16
16
Maytag Cabrio,- WED5500X Installation instructions manual - Page 17
17
Maytag Cabrio,- WED5500X Installation instructions manual - Page 18
18
Maytag Cabrio,- WED5500X Installation instructions manual - Page 19
19
Maytag Cabrio,- WED5500X Installation instructions manual - Page 20
20
12
1. Prepare to connect neutral
ground wire and neutral wire
A
E
B
Remove center, silver-colored terminal block screw (B).
Remove neutral ground wire (E) from external ground
conductor screw (A).
E
B
C
Connect neutral ground wire
and neutral wire
2.
Connect neutral ground wire (E) and neutral wire (white or
center wire) (C) of power supply cord or cable under center,
silver-colored terminal block screw (B). Tighten screw.
Connect remaining wires
3.
Place hooked ends of remaining wires under outer terminal
block screws (hooks facing right). Tighten screws.
A
G
Connect external ground wire
4.
Connect a separate copper ground wire (G) from the external
ground conductor screw (A) to an adequate ground. Finally,
reinsert tab of terminal block cover into slot of dryer rear
panel. Secure cover with hold-down screw. Now, go to
Venting Requirements.
Optional 3-wire Connection
You must verify with a qualied electrician that this
grounding method is acceptable before connecting.
Connect remaining wires
7.
Place hooked ends of remaining direct wire cable wires
under outer terminal block screws (hooks facing right).
Squeeze hooked ends together and tighten screws. Finally,
reinsert tab of terminal block cover into slot of dryer rear
panel. Secure cover with hold-down screw. Now, go to
Venting Requirements.
B
C
Place hooked end of neutral wire (white or cente) (C) of direct
wire cable under center terminal block screw (B). Squeeze
hooked end together. Tighten screw.
6. Connect neutral wire