Maytag 1800 W - 2005 Manual 

Download Manual  of Maytag 1800 W - 2005 Microwave Oven for Free or View it Online on All-Guides.com.

Maytag 1800 W - 2005 Manual  - Page 1
1
Maytag 1800 W - 2005 Manual  - Page 2
2
Maytag 1800 W - 2005 Manual  - Page 3
3
Maytag 1800 W - 2005 Manual  - Page 4
4
Maytag 1800 W - 2005 Manual  - Page 5
5
Maytag 1800 W - 2005 Manual  - Page 6
6
Maytag 1800 W - 2005 Manual  - Page 7
7
Maytag 1800 W - 2005 Manual  - Page 8
8
Maytag 1800 W - 2005 Manual  - Page 9
9
Maytag 1800 W - 2005 Manual  - Page 10
10
Maytag 1800 W - 2005 Manual  - Page 11
11
Maytag 1800 W - 2005 Manual  - Page 12
12
Maytag 1800 W - 2005 Manual  - Page 13
13
Maytag 1800 W - 2005 Manual  - Page 14
14
Maytag 1800 W - 2005 Manual  - Page 15
15
Maytag 1800 W - 2005 Manual  - Page 16
16
Maytag 1800 W - 2005 Manual  - Page 17
17
Maytag 1800 W - 2005 Manual  - Page 18
18
Maytag 1800 W - 2005 Manual  - Page 19
19
Maytag 1800 W - 2005 Manual  - Page 20
20
Maytag 1800 W - 2005 Manual  - Page 21
21
Maytag 1800 W - 2005 Manual  - Page 22
22
Maytag 1800 W - 2005 Manual  - Page 23
23
Maytag 1800 W - 2005 Manual  - Page 24
24
Maytag 1800 W - 2005 Manual  - Page 25
25
Maytag 1800 W - 2005 Manual  - Page 26
26
Maytag 1800 W - 2005 Manual  - Page 27
27
Maytag 1800 W - 2005 Manual  - Page 28
28
Maytag 1800 W - 2005 Manual  - Page 29
29
Maytag 1800 W - 2005 Manual  - Page 30
30
Maytag 1800 W - 2005 Manual  - Page 31
31
Maytag 1800 W - 2005 Manual  - Page 32
32
Maytag 1800 W - 2005 Manual  - Page 33
33
Disassembly Procedures
To avoid the risk of electrical shock, personal injury, or death,
disconnect power to oven and discharge the capacitors before
following any disassembly procedure.
WARNING
!
30 16026795 ©2006 Maytag Services
Magnetron Thermal Cut-Out (TCO)
1. Disconnect power to oven and remove outer case,
(see "Outer Case" procedure).
2. Remove outer case.
3. Remove screw securing bottom portion of duct
assembly securing bottom TCO.
4. Bend metal tab securing top TCO located above top
magnetron.
5. Disconnect and label wiring.
6. Replace component and reverse procedure to
reassemble.
NOTE: When reconnecting wiring to thermal fuses the
connectors must be tight.
Cavity Thermal Fuse
1. Disconnect power to oven and remove outer case,
(see "Outer Case" procedure).
2. Remove outer case.
3. Remove screw securing cavity thermal fuse.
4. Disconnect and label wiring.
5. Replace component and reverse procedure to
reassemble.
NOTE: When reconnecting wiring to thermal fuses the
connectors must be tight.
Tray Replacement
1. Unplug oven from outlet.
2. Use a suction cup to pry upward on front portion and
remove tray from unit.
3. Thoroughly clean and degrease sump area.
4. Clean oven cavity bottom where new oven tray will
make contact using mineral spirits or any
non-flammable degreasing solvent.
NOTE: Detergents, soap, and water are not sufficient to
remove oil and grease.
5. Clean cavity with mild detergent to remove any
remaining degreasing solvent and place new tray into
unit.
Oven Light Removal
The light bulb for inside of the oven can be changed only
from the side of the unit. On the left hand side of the oven
is a metal plate with one screw. The light bulbs are
located behind this plate.
Follow these steps to change the bulb:
1. Disconnect power to oven.
2. Remove screw and plate from side of unit.
3. To remove bulb, turn it counterclockwise, being
careful not to burn fingers or break the bulb.
4. Replace bulb with a 20 watt, 230 - 240 volt appliance
bulb.
5. Reposition plate, being careful not to bend hinge tab.
Replace and tighten screw. Do not operate oven
without plate in place.