Home | About | Contact

Maytag MMV1164WB5 Installation Instructions Manual

Download Installation instructions manual of Maytag MMV Microwave Oven for Free or View it Online on All-Guides.com. This version of Maytag MMV Manual compatible with such list of devices, as: MMV, MMV1164WB2, MMV1164WS6, MMV5208WS1, MMV5208WW1

Maytag MMV Installation instructions manual - Page 1
1
Maytag MMV Installation instructions manual - Page 2
2
Maytag MMV Installation instructions manual - Page 3
3
Maytag MMV Installation instructions manual - Page 4
4
Maytag MMV Installation instructions manual - Page 5
5
Maytag MMV Installation instructions manual - Page 6
6
Maytag MMV Installation instructions manual - Page 7
7
Maytag MMV Installation instructions manual - Page 8
8
Maytag MMV Installation instructions manual - Page 9
9
Maytag MMV Installation instructions manual - Page 10
10
Maytag MMV Installation instructions manual - Page 11
11
Maytag MMV Installation instructions manual - Page 12
12
VENTING DESIGN SPECIFICATIONS
This section is intended for architectural designer and
builder/contractor reference only.
NOTES:
Vent materials needed for installation are not provided with
microwave hood combination.
We do not recommend using a flexible metal vent.
To avoid possible product damage, be sure to vent air
outside, unless using recirculation installation. Do not vent
exhaust air into concealed spaces, such as spaces within
walls or ceilings, attics, crawl spaces or garages.
Rectangular to Round Transition
NOTE: The minimum 3" (7.6 cm) clearance must exist between
the top of the microwave oven and the rectangular to round
transition piece so that the damper can open freely and fully.
For optimal venting installation, we recommend:
using roof or wall caps that have back draft dampers
using a rigid metal vent
using the most direct route by minimizing the length of the
vent and number of elbows to provide efficient performance
using uniformly sized vents
using duct tape to seal all joints in the vent system
using caulking compound to seal exterior wall or roof opening
around cap
not installing 2 elbows together, for optimal hood performance
If venting through the wall, be sure that there is proper clearance
within the wall for the damper to open fully.
If venting through the roof, and rectangular to round transition is
used, be sure there is at least 3" (7.6 cm) of clearance between
the top of the microwave oven and the transition piece. See
"Rectangular to Round Transition" illustration.
f
A. Roof cap
B. 6" (15.2 cm) min. diameter round vent
C. Elbow (for wall venting only)
D. Wall cap
E. 3 ¼" x10" to 6" (8.3 x 25.4 cm to 15.2cm)
rectangular to round transition piece
E Vent extension piece, at least 3" (7.6 cm) high
Recommended Standard Fittings
The following length equivalents are for use when figuring vent
length. See the examples in "Recommended Vent Length."
A B C
Roof venting Roof cap
Wall venting Wall cap
D E F G
A. Rectangular to round transition piece: 3¼" x 10" to 6" = 5 ft
(8.3 x 25.4 cm to 15.2 cm = 1.5 m)
B. Roof cap: 3 ¼" x 10" = 24 ft (8.3 x 25.4 cm = 7.3 m)
C. 90 ° elbow: 3 ¼" x 10" = 25 ft (8.3 x 25.4 cm = 7.6 m)
D. 90 ° elbow: 6" = 10 ft (15.2 cm = 3 m)
E. Wall cap: 3 ¼" x 10" = 40 ft (8.3 x 25.4 cm = 12.2 m)
E 45 ° elbow: 6" = 5 ft (15.2 cm = 1.5 m)
G. 90° flat elbow: 3 ¼" x 10" = 10 ft (8.3 x 25.4 cm = 3 m)
11