Home | About | Contact

Maytag MMV1164WB5 Installation Instructions Manual

Download Installation instructions manual of Maytag MMV Microwave Oven for Free or View it Online on All-Guides.com. This version of Maytag MMV Manual compatible with such list of devices, as: MMV1164WB2, MMV1164WS6, MMV4206BW0, MMV5208WS1, MMV6180WW1

Maytag MMV Installation instructions manual - Page 1
1
Maytag MMV Installation instructions manual - Page 2
2
Maytag MMV Installation instructions manual - Page 3
3
Maytag MMV Installation instructions manual - Page 4
4
Maytag MMV Installation instructions manual - Page 5
5
Maytag MMV Installation instructions manual - Page 6
6
Maytag MMV Installation instructions manual - Page 7
7
Maytag MMV Installation instructions manual - Page 8
8
Maytag MMV Installation instructions manual - Page 9
9
Maytag MMV Installation instructions manual - Page 10
10
Maytag MMV Installation instructions manual - Page 11
11
Maytag MMV Installation instructions manual - Page 12
12
INSTALLATION REQUIREMENTS
Tools Needed
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools
listed here.
Measuring tape Stud finder
Pencil 7/16" socket wrench
(or box wrench) for 1/4" x
Masking tape or 2" lag screws
thumbtacks
Scissors 1_/2"(3.8 cm) diam. hole
drill bit for wood or metal
No. 2 Phillips screwdriver cabinet
No. 3 Phillips screwdriver Keyhole saw
for 1/4-20 x 3" bolts
Caulking gun and
Drill weatherproof caulking
compound
3/16" (5 mm), 3/8" (10 mm)
drill bits Duct tape
3/4" (19 mm) hole saw
Parts Supplied
For reorder information, see "Replacement Parts" section.
NOTE: The hardware items listed here are for wood studs. For
other types of wall structures, be sure to use appropriate
fasteners.
A
A. 1/4-20 x 3" round-head bolts (2)
B. 1/4-20 x 3" flat-head bolts (2)
C. Washers (2)
D. Toggle nuts (2)
E. 1/4 " x 2" lag screws (2)
F. Sheet metal screws (2)
G. Power supply cord bushing (1)
H. Damper assembly (for wall or roof
venting)
Not Shown:
Upper cabinet template
Mounting plate (attached to
back of microwave oven)
Cardboard template (part
of packaging)
Aluminum grease filters
Charcoal filters (Depending
on model, charcoal filters
may not be included. See
User Instructions.)
NOTE: Depending on model, aluminum grease filter and charcoal
filter may be combined.
Materials needed
Standard fittings for wall or roof venting. See "Venting Design
Specifications" section.
The cardboard piece from the top of the microwave oven
packaging is perforated. The piece inside the perforation is for use
as a rear wall template.
1. Cut along the perforation to separate the template from the
rest of the cardboard packaging.
2. Set the cardboard template to the side and refer to it during
the "Mark Rear Wall" part of installation.
Check the opening where the microwave oven will be installed.
The location must provide:
Minimum installation dimensions. See "Installation
Dimensions" illustration.
Minimum one 2" x 4" (50.8 x 101.6 mm) wood wall stud and
minimum 3/8" (10 mm) thickness drywall or plaster/lath within
cabinet opening.
Support for weight of 150 Ibs (68 kg), which includes
microwave oven and items placed inside the microwave oven
and upper cabinet.
Grounded electrical outlet inside upper cabinet. See
"Electrical Requirements" section.
NOTES:
If installing the microwave oven near a left sidewall, make sure
there is at least 6" (15.2 cm) of clearance between the wall and
the microwave oven, so that the door can open fully.
Some cabinet and building materials are not designed to
withstand the heat produced by the microwave oven for
cooking. Check with your builder or cabinet supplier to make
sure that the materials used will not discolor, delaminate or
sustain other damages.
Special Requirements
For Wall Venting Installation Only:
Cutout must be free of any obstructions so that the vent fits
properly, and the damper blade opens freely and fully.
For Roof Venting Installation Only:
If you are using a rectangular to round transition piece, the
3" (7.6 cm) clearance needs to exist above the microwave
oven so that the damper blade can open freely and fully. See
"Rectangular to Round Transition" illustration in "Venting
Design Specifications" section.