• Home
• Brands
• Maytag Manuals
• Maytag MMV1163DB00
• Maytag MMV1163DW00 Installation Instructions Manual

Maytag MMV1163DW00 Installation Instructions Manual

Download Installation instructions manual of Maytag MMV1163DB00 Microwave Oven for Free or View it Online on All-Guides.com.

1

2

3

4

5

6

7

8

9

10

11

12

7,

Holding the mounting plate in place, and making sure it is

aligned with the top edge line, centerline and the mounting

holes, find the wall stud centerline(s) drawn in Step 2 of

"Locate Wall Stud(s)." Mark 1 hole through the mounting

plate, closest to the wall stud centerline. See illustrations in

"Locate Wall Stud(s)" section. The blackened holes in the

shaded areas are ideal hole locations.

NOTE: If there are 2 wall studs in the opening, mark the hole over

the wall stud to the right of the opening's centerline, as the

microwave oven is heavier on its right-hand side. See Figure 2 in

"Locate Wall Stud(s)" section.

8. Set the mounting plate aside.

Wall Venting Installation Only

Centerline Upper cabinet bottom

........ 1

I t

4" (10.2crn)

6" (15.2 crn)

%" (1 cm)

6" (15.2 crn)

9. Mark the centerline 3/8" (1 cm) down from the bottom edge of

the upper cabinet.

10. Using measuring tape, measure out 6" (15.2 cm) on both sides

of the centerline, and mark.

11. Measure down 4" (10.2 cm) from the mark made in Step 9,

and mark.

12. Using a straightedge, draw the 2 horizontal, level lines through

the marks made in steps 9 and 11.

13. Draw the 2 vertical, plumb lines down from the marks made in

Step 7 to complete the 12" x 4" (30.5 x 10.2 cm) rectangle.

This is the venting cutout area.

14. Cut a 3/4" (19 mm) hole in one corner of the cutout area.

15. Using a keyhole saw, cut out the venting cutout area.

In addition to being installed on a wall stud, the mounting plate

must attach to the wall through mounting holes on both ends.

If the mounting holes are not over wall studs, use two 3/16-20 x 3"

hex-head bolts with toggle nuts. If 1 hole is over a wall stud, use

1 lag screw and one 3/16-20 x 3" hex-head bolt with toggle nut.

If both end mounting holes are over wall studs, use a lag screw at

the right side mounting hole, and use one 3/16-20 x 3" hex-head

bolt with toggle nut at the new mounting hole marked in Step 6 of

"Mark Rear Wall."

1. Drill 5/8" (16 mm) hole(s) through the wall at holes marked for

3/16-20 x 3" hex-head bolt(s) with toggle nut(s).

2. Drill 1/8" (3 mm) hole into the wall stud at the hole marked in

Step 7 of "Mark Rear Wall." Refer to illustrations in "Locate

Wall Stud(s)" section.

All< ,.I_ ...... o '.........

NOTE: Secure the mounting plate to the wall at both end

mounting holes drilled into the wall studs and/or drywall using

either two 3/16-20 x 3" hex-head bolts with toggle nuts, or one

3/16-20 x 3" hex-head bolt with toggle nut and one 3/16 x 2" lag

screw.

Refer to illustrations in "Locate Wall Stud(s)" section.

1. With the support tabs of the mounting plate facing forward,

insert 3/16-20 x 3" hex-head bolt(s) through end mounting

hole(s) that is(are) not over wall stud(s). Start toggle nut(s) on

bolt(s) from the back of the mounting plate. Leave enough

space for the toggle nut(s) to go through the wall and to open.

2.

3.

4,

5.

6.

................................c

A. 3/16-20 x 3" hex-head bolt

B. Mounting plate

C.Spring toggle nut

Position mounting plate on the wall.

Push the bolt(s) with toggle nut(s) through the drywall, and

finger tighten the bolt(s) to make sure toggle nut(s) has(have)

opened against drywall.

i_......................................................C

| O

B ...........................................................................7/

A. 3/16-20 x 3" hex-head bolt

B. Mounting plate

C.Drywall

D.Spring toggle nut

Insert lag screw into the hole drilled into wall stud in Step 2 of

"Drill Holes in Rear Wall."

Check alignment of mounting plate, making sure it is level.

Securely tighten lag screw and bolts.