• Home
• Brands
• Maytag Manuals
• Maytag MHN30PDBGW
• Maytag MHN30PDBGW Installation Instructions Manual

Maytag MHN30PDBGW Installation Instructions Manual

Download Installation instructions manual of Maytag MHN30PDBGW Vacuum Cleaner, Washer for Free or View it Online on All-Guides.com.

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

15

Washer Diagnostic Modes

To enter the “Washer Diagnostic Mode,” rst enter “Start

Operating Set-up.” Then press and hold the QUICK CYCLE

button for 1 second while in set-up code 6, anytime a diagnostic

code is present, or while dAS displays if operating with Maytag

Data Acquisition set-up.

On entry to diagnostic mode the entire display will ash, a

cycle in process is canceled, money in escrow is cleared, and

diagnostic codes are cleared. If a diagnostic code persists,

it must be corrected before the following cycle options are

permitted.

There are ve possible ways to initiate cycle activity from

diagnostic mode as follows:

1. Washer Cleanout cycle - With the entire display ashing, this

cycle is started by pressing the BRIGHTS button.

Use the Washer Cleanout cycle once a month to keep the

inside of your washer fresh and clean. This cycle uses

a higher water level. Use with liquid chlorine bleach to

thoroughly clean the inside of the washer. This cycle should

not be interrupted.

IMPORTANT: Do not place garments or other items in the

washer during the Washer Cleanout cycle. Use this cycle with

an empty wash drum.

2. Cycle Credit - With the entire display ashing, a cycle may

be credited by pressing the PERM. PRESS button (CC will

display). When the service mode is exited, “SELECT CYCLE”

will be displayed unless the end-of-cycle door opening is

required.

3. Manual Overview Test - With the entire display ashing, this

cycle is started by pressing the WHITES button. This cycle

provides more typical full length lls, tumbles, drains, and

actuator dispenser movement, allowing for a more thorough

analysis of the washer operation, including pressure switch

behavior.

4. Quick Spin Cycle - With the entire display ashing, this

cycle is started by pressing the COLORS button. This cycle

provides a method to quickly drain and spin (remove water

from the washer) if desired.

5. Quick Overview Test - With the entire display ashing, this

cycle is started by pressing the DELICATES AND KNITS

button. This cycle provides a quick verication that the cold

and hot water valves, dispensers, and pump motor are

working, as well as actuator dispenser movement. It also

includes door lock, drain, and spin operations.

Pressing the QUICK CYCLE button will exit diagnostic mode

and cancel a diagnostic cycle in process.

DIAGNOSTIC CODES

If one of the following has occurred, the appropriate diagnostic

code will be in the display.

d5 Blocked coin 1 or coin drop control circuit failure (coin

recognition and price display disabled while blockage

persists).

PN Models Only: Set-up mode J. should be set

to _d to eliminate coin related diagnostic codes.

d9 Low voltage detected for 8 seconds.

d13 Blocked coin 2 or coin drop control circuit failure (coin

recognition and price display disabled while blockage

persists).

F20 Slow Fill. The washer will not detect water input for 4 min.

Pressure switch failure or no water inlet. This code is

reported as d8 on d7.

F22 The door is not able to lock. Door lock error or someone

trying to start the washer, by pressing the door switch

with the nger. This code is reported as d17 on Accu Trac.

(For any other codes, check supplied Technical Sheet)

SERVICE ACCESS CODE

This code can be entered to access service mode without

removing the console. It only functions on washers set up for

0 vend price without any Special Pricing set-up, and the Coin/

Debit Option must be set to “J._d”. If the washer is not in failure

mode, the door must be opened to proceed. Service Access

Code contains 6 steps and some are timed. Using only the three

bottom buttons (numbered 1, 2, and 3 from left to right):

1. Press 2 for longer than 2 seconds but less than 10 seconds.

2. Press 1 & 3 together for 2 seconds, then release.

Displays S 3.

3. Press 1 & 2 together, then release. Displays S 4.

4. Press 2 & 3 together, then release. Displays S 5.

5. Press 2, then release. Display shows “codE”.

6. Wait at least 2 seconds, but not more than 15 seconds, then

press in succession: 3, 2, 1, 3.

NOTE: If the Service Access Code procedure is not completed

properly, as noted above, there is a 15 second delay before it can

be attempted again.

There are 3 options to exit from the Service Mode:

1. From Set-up Code 8, press key #1 for 4 seconds.

2. Wait 2 minutes without touching any buttons (without

diagnostic modes running).

3. Power down the washer, then reapply power.

WASHER HELP MODE

This mode is entered by pressing the PERM. PRESS button while

in special pricing option mode 2.XX (or while dAS displays if

operating with Maytag Data Acquisition set-up).

In help mode, other display symbols and elements are mapped to

reect the state of various inputs and outputs as follows:

Display Symbol Description

Wash Water sensed at wash level.

* Low voltage present (below about

90 VAC).

° (Circle above digit) Door closed

DOOR LOCKED Door sensed locked.

COLD Cold water relay on.

HOT Hot water relay on.

OR Door unlock.

AVAILABLE Drain pump ON.

NOTE: A Technical Sheet is supplied taped to inside of lower

front panel, which includes fault codes and a machine schematic

diagram.