Maytag MHN30PDBGW Installation Instructions Manual
Download Installation instructions manual of Maytag MHN30PDBGW Vacuum Cleaner, Washer for Free or View it Online on All-Guides.com.
Brand: Maytag
Category: Vacuum Cleaner , Washer
Type: Installation instructions manual
Model: Maytag MHN30PDBGW , Maytag MHN30PNBGW
Pages: 36
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
5
Location Requirements
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer “walk.”
Your washer can be installed under a custom counter, or in a
basement, laundry room, or recessed area. See “Drain System.”
Companion appliance location requirements should also be
considered. Proper installation is your responsibility.
You will need
■ A water heater set to deliver 49°C (120°F) water to the
washer.
■ A grounded electrical outlet located within 1.8 m (6 ft.) of
where the power cord is attached to the back of the washer.
See “Electrical Requirements.”
■ Hot and cold water taps located within 1.2 m (4 ft.) of
the hot and cold water ll valves, and water pressure of
137.9-689.6 kPa (20-100 psi).
■ A level oor with a maximum slope of 25 mm (1") under entire
washer. Installing the washer on soft oor surfaces, such as
carpets or surfaces with foam backing, is not recommended.
■ A sturdy and solid oor to support the washer with a total
weight (water and load) of 180 kg (400 lbs).
Do not operate your washer in temperatures below 0°C (32°F).
Some water can remain in the washer and can cause damage
in low temperatures.
Installation clearances
■ The location must be large enough to allow the washer
door to be fully opened.
■ Additional spacing should be considered for ease of
installation and servicing. The door opens more than 90°,
and it is not reversible.
■ Additional clearances might be required for wall, door, and
oor moldings.
■ Additional spacing of 1" (25 mm) on all sides of the washer
is recommended to reduce noise transfer.
■ Companion appliance spacing should also be considered.
Washer Dimensions
1282 mm
(50
1
/2")
961 mm
(37
13
/16")
686 mm
(27")
732 mm
(28
13
/16)
1134 mm
(44
5
/8")
A oor drain should be provided under the bulkhead.
Prefabricated bulkheads with electrical outlets, water inlet
lines, and drain facilities should be used only where local
codes permit.
Drain System
The washer can be installed using the standpipe drain system
(oor or wall), the laundry tub drain system, or the oor drain
system. Select the drain hose installation method you need.
See “Tools and Parts.”
Standpipe drain system – wall or oor (views A & B)
The standpipe drain requires a minimum diameter standpipe of
50 mm (2"). The minimum carry-away capacity can be no less
than 45.5 L (12 gal.) per minute, per washer.
The top of the standpipe must be at least 762 mm (30") high and
no higher than 2.4 m (96") from the bottom of the washer.
A
762 mm
(30" min.)
B
Laundry tub drain system (view C)
The laundry tub needs a minimum 76 L (20 gal.) capacity. The top
of the laundry tub must be at least 762 mm (30") above the oor.
Floor drain system (view D)
The oor drain system requires a siphon break that may be
purchased separately. See “Tools and Parts.”
The siphon break must be a minimum of 710 mm (28") from the
bottom of the washer. Additional hoses might be needed.
762 mm
(30" min.)
710 mm
(28" min.)
C D
Door is not reversible